Best sellers

Shield with dual-channel DC motor driver for Arduino. It has an operating voltage from 7 to 30 V and a continuous current of up to 10 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron SHIELD-MDD10

Soldering tip ET SL mounted on a heater. Fits Weller LR 21, WEP 70 and FE 50 soldering irons.

DEV-14352

Module with 4-channel ADC ADS1015 converter. The system enables analog voltage conversion for both single signals (11-bit resolution) and differential signals (12-bit resolution). I2C communication. SparkFun DEV-15334

Power module with a USB Type-C connector based on the STUSB4500 system. It enables powering devices with voltages ranging from 5 V to 20 V and currents up to 5 A. Configuration via the I2C interface. SparkFun DEV-15801

Compact board for controlling RGB and white LED strips, allowing easy connection without the need for soldering. With WS2811F and N-channel FETs, it supports up to 3A of current per channel, making it ideal for high-current LED strips, but does not support RGBW strips. Adafruit 5888

Single board computer with ARM Cortex-A8 AM335x processor, clocked at 1 GHz with 512 MB of RAM. The module has, among others USB interfaces, I / O pins, WiFi and Bluetooth. SeeedStudio 102010048

Module with E-Ink display with a resolution of 250x122 pixels and a diagonal of 2.13 inches. Designed for the Raspberry Pi computer (HAT overlay). SPI interface communication. Waveshare 2.13inch e-Paper HAT

A module that provides galvanically isolated, bidirectional I²C communication (SDA and SCL lines), protecting devices from incorrect connections and voltage differences. Thanks to the TI ISO1640B chip, it supports data transfer up to 1.7 MHz. Pololu 5390

Nylon PA12 filament in Black with a diameter of 1.75 mm. 0,75 kg of filament is wound on a spool. Fiberlogy Nylon PA12 Black

Module with the MCP9600 amplifier designed to work with a K-type thermocouple. The module has a PCC connector for connecting this type of thermocouple. I2C communication. SparkFun SEN-16294

The S9V11F3S5C3 switching step-up/step-down regulator efficiently produces a fixed 3.3 V (default) or 5 V (selectable) output whether it is higher or lower than the input voltage, which can range from 3 V to 16 V. The regulator also has fixed 3.3 V low-voltage cutoff with hysteresis that can be used to prevent battery over-discharge.

The S9V11F5S6CMA switching step-up/step-down regulator efficiently produces a fixed 5 V (default) or 6 V (selectable) output whether it is higher or lower than the input voltage, which can range from 2 V to 16 V. (Note: minimum start-up voltage is 3 V, but it operates to 2 V after that.)

2-CHANNEL THERMOMETER - PLATE AND PROGRAMMED LAYOUT

The S9V11MACMA switching step-up/step-down regulator efficiently produces a finely adjustable output between 2.5 V and 9 V whether it is higher or lower than the input voltage, which can range from 3 V to 16 V. The regulator also has a precision-adjustable low-voltage cutoff with hysteresis that can be used to prevent battery over-discharge.

Nylon PA12 filament in White with a diameter of 1.75 mm. 0,75 kg of filament is wound on a spool. Fiberlogy Nylon PA12 White

The GPS receiver is equipped with a GP-735T module. It is supplied with the voltage from 3.3 to 5.5 V and communicates via the UART interface. SparkFun GPS-13670

Nylon PA12 filament in Natural with a diameter of 1.75 mm. 0.75 kg of filament is wound on a spool. Fiberlogy Nylon PA12 Natural

The FS5106R is a standard-sized servo that has been built by FEETECH specifically for continuous rotation, making it an easy way to get your robot moving. It features two ball bearings on the output shaft for reduced friction, and it offers easy access to the rest-point adjustment potentiometer.