Best sellers
There are 16464 products.
A walking robot powered by wind. A great toy for children
Module with MLX90641 thermal imaging camera with a 16x12 field matrix and a viewing angle of 55°. It communicates via the I2C interface. Waveshare MLX90641-D55 Thermal Camera
Set of 24 keycaps for keyboard. They have a milky-transparent layer, thanks to which they perfectly match the LED backlight. Adafruit 5148
Module with a black and white OLED display 1.3" with a resolution of 128x64 pixels. Designed for M5Stack sets. It communicates via the I2C interface. M5Stack U119
RC extension cable dedicated to servos, comes with JR/Futaba female and male connectors
Module with the OPTIGA TRUST M SLS32AIA cryptographic chip. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4351
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
A 7-pin cable with a length of 30 cm, terminated on both sides with a Molex Picoblade 1.25 mm plug
This gearmotor is a miniature medium-power, 6 V brushed DC motor with a 297.92:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft.
A set of connectors with a crimper in the cassette. The tool is used for crimping non-insulated connectors AWG 22-18 / 16-14 / 10-8, has the option of cutting wires and removing insulation
Multifunctional tool for clamping connectors and coaxial connectors RG58, RG6, RG174, has a locking function and the ability to adjust the pressure. HT-301B
NUCLEO series starter kit equipped with a STM32WL55JC microcontroller (256 KB Flash, Cortex-M4/M0+), with a built-in STLINK-V3E programmer-debugger, equipped with Arduino-compatible connectors
Motor with 25 mm diameter and 58 mm length, 378:1 metal gear, 12 V operating voltage, 0,1 A to 1,1 A power consumption, 14 RPM speed and 23 maximum torque. Pololu 3258
A set of DIP sockets for through hole circuits. Includes 6, 8, 14, 16, 18, 20, 24 and 28-pin sockets
The UM7-LT orientation sensor from Redshift Labs is an Attitude and Heading Reference System (AHRS) that contains a three-axis accelerometer, rate gyro, and magnetometer. It combines this data using an Extended Kalman Filter to produce attitude and heading estimates. This LT version of the UM7 does not have an enclosure.
The quartz heater is used for preheating the PCB using quartz glass, prevents overheating and damage during soldering. WEP 853A
The board features a Zynq XC7Z020, Ethernet, HDMI in/out, MIC in, Audio out, Arduino Interface, 2 Pmods, 16 pin GPIO header, user LEDs, pushbuttons and Switches. 6003-410-0
Module with a 6-axis IMU sensor (accelerometer and gyroscope) that allows you to measure acceleration and rotational speed in a wide range of ±30g and ±4000dps. Communicates via I2C. Adafruit 4464
Module with an ISO1540 bidirectional galvanic isolator. It allows to electrically separate two devices communicating via the I2C interface. Adafruit 4903