Best sellers

LED strip with COB diodes in red. It is powered by 12 V DC, has a length of 1 m and 384 LEDs/m. Protection level IP20

LED strip with COB diodes in red. It is powered by 12 V DC, has a length of 5 m and 384 LEDs/m. Protection level IP20

Raspberry Pi Expansion Board, Power Relay, Waveshare

This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 986.41:1 metal gearbox, making it a great choice for applications requiring fine control at very low speeds. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter.

LED strip with addressable RGB WS2813 diodes on a black PCB. It is powered by 5 V DC, has a length of 1 m and 144 LEDs/m. Protection degree IP67

EL-wire are thin and flexible wires that glow under the influence of high voltage power. Includes battery charger, splitter and five el-wire wires with a length of 1m

The magnetic holder is an ideal solution for mounting small USB monitors or phones. It provides a stable grip and is easy to install. Waveshare Magnetic Holder

Installation connector, 5-wire, 450 V, 32 A, with levers. Wago 221-415

Development platform for cellular IoT devices. The kit includes a Discovery motherboard equipped with the LBAD0ZZ1SE module, which includes an STM32L462REY6TR microcontroller, an LTE Cat M/NB LBAD0XX1SC-DM modem and a built-in SIM card. STMicroelectronics B-L462E-CELL1

The X-NUCLEO-53L0A1 expansion board features the VL53L0X ranging and gesture detection sensor, based on ST’s FlightSense™, Time-of-Flight technology. It is an evaluation board that provides an introduction to the ranging and gesture detection capabilities of the VL53L0X module

Isolated USB - RS232/RS485/RS422/TTL converter dedicated to industrial applications. It offers 4 channels for serial communication, including TTL channel, TTL/RS485, isolated RS485/422 channel and isolated RS232/485 channel. Provides easy communication between the USB interface and serial communication standards. Waveshare USB TO 4CH Serial Converter

RTC clock module with a built-in Watchdog system dedicated to projects based on Raspberry Pi minicomputers. It is equipped with an advanced monitoring circuit with the CH32V003 chip, which allows for automatic reset in the event of system malfunction or freeze. Waveshare RTC Watchdog HAT (B)

RGB LED matrix display with a resolution of 64x32 (2048 LEDs). It has a HUB75 interface and can work with Raspberry Pi, Arduino or ESP32. Waveshare RGB-Matrix-P5-64x32

A board with an ESP32 module equipped with a 1.28-inch touch screen. It offers Wi-Fi and Bluetooth 5.0 communication and has a built-in 6-axis QMI8658 IMU sensor and supports charging lithium batteries. Perfect for developing IoT, mobile devices and wearable electronics projects. Waveshare ESP32-S3-Touch-LCD-1.28

The SMA male crimp connector for cable is a standard connector used in a wide range of radiocommunication and electronic devices. It is made of anodized brass. It has an impedance of 50 Ω, which is a standard parameter for many radio communication systems

Compact engine with 75: 1 LP transmission, shaft speed is 290 rpm, torque is 0.8 kg * cm (0.08 Nm), plate with connector PH 2.0. DFRobot FIT0457

Antenna with MCX male connector operating in the 1090 MHz frequency band. It has a gain of 3.5 dBi and a 1 m cable. Magnetically attached

Adapter with a set of connectors specific to the Raspberry Pi 3 Model B/B+. It allows you to adapt the Raspberry Pi CM4 modules to projects based on Pi 3 model B/B+. Waveshare CM4-to-Pi3-Adapter-B

The A-Cute Car is an FPGA-based three-wheeled robotic car kit. This car can provide higher operation performance than the MCU based robotic car, because the FPGA provides more powerful computing power than the MCU. P0467

A set of 40 pcs of male-female connecting cables in various colors, 10 cm long