Best sellers
There are 17621 products.
Gravity: The high temperature sensor is a sensor based on the PT100 probe and adapted to very high temperatures (30-350 ° C). The module is powered by 3.3 ... 5.5V voltage. DFRobot SEN0198
Module with 8 Mpx camera with IMX219 sensor and wide-angle "fisheye" lens. Designed for Nvidia Jetson Nano and Raspberry Pi Compute Module. ArduCAM B0287
This gearmotor is a miniature high-power, 12 V brushed DC motor with long-life carbon brushes and a 100.37:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft.
Key specs at 12 V: 320 RPM and 100 mA with no load, 30 oz-in (2.2 kg-cm) and 0.8 A at stall.
The module with the IMX230 sensor, working with all versions of the Raspberry Pi. The sensor used has a matrix of 21 MP and allows you to record video at resolutions of 5344x4012/9fps. ArduCAM B0324
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 20 A. DFRobot SEN0211
DC Micro motor module with metal gear with a gear ratio of 30:1. The motor is connected to the board containing the driver. DFRobot DFR0399
A set of conductive materials dedicated to device prototyping. DFRobot FIT0823
Ethernet network module with W5500 chip and PoE (Power over Ethernet) function. It communicates via the SPI interface, it has a built-in TCP/IP stack. DFRobot DFR0850
El-wire is a thin and flexible wire which shines under high voltage. The cable is red, has a diameter of 3mm and a length of 3 meters
This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller’s analog-to-digital converter. Each breakout comes fully assembled and works from 2.7V up to 5.5V. BOB-12758
The module with the converter USB-UART CP2104 dedicated for minicomputers Raspberry Pi. Adafruit 3589
A two-piece aluminum adapter for transmitting wheel drive to motors with a 4mm diameter shaft. Mounting screws and set screws included. Pololu 2672
Set of "sleeping lion" with the educational module micro: bit. It consists of a main plate, noise: bit and felt elements, thread and needle to create the toy. Pimoroni PIM363
Module with 3.5 mm TRS connector for MyoWare 2.0 muscle tension sensors. It allows you to conveniently connect the sensors with the development board via the Arduino shield. SparkFun DEV-18386
ToF distance sensor (Time of flight) with a range of up to 5 m. The module is supplied with the voltage of 3.3 V and communicates via the I2C interface. SparkFun SEN-19218
STM32 Nucleo development board for STM32 L0 series - with STM32L053R8 MCU, 64KB flash memory, STM, RoHS
Module with OV5647 sensor cooperating with ODROID-M1. It uses a built-in movable IR-CUT filter that is turned on and off automatically depending on the lighting conditions. Odroid M1 MIPI-CSI Camera Kit
ATATMEL-ICE-BASIC is a programmer designed to work with AVR microcontrollers with the On-Chip Debug function and microcontrollers with the ARM Cortex-M core from Atmel. Available interfaces are JTAG, SWD, PDI, TPI, aWire, SPI and debugWire.
The power module is designed for the MyoWare 2.0 muscle tension sensor. Equipped with a LiPo battery, it allows you to build portable devices. SparkFun DEV-18427