Best sellers
There are 16539 products.
Adapter for the 6-pin JST SH connector (vertical) with a pitch of 1 mm to the DIP holes, pitch of 2.54 mm. The set includes 3 modules. Pololu 4771
Module with 32 12 V relays with a maximum switching current of 7 A. It communicates via the USB interface. Numato Lab RL320001
Industrial 4G LTE router that provides reliable communication for M2M and IoT applications. Equipped with WAN port, LAN port and SIM card slot. USR-G806-E
Gravity: Heart Rate Monitor Sensor is a sensor used to measure heart activity. Adapted for easy use with Arduino. SparkFun SEN0213
Vertigo PCTG filament with a diameter of 1.75 mm. 0.75 kg of filament is wound on the spool. Fiberlogy PCTG Vertigo
Module with 4 5 V relays with a maximum switching current of 2 A. It communicates via the USB interface and does not require an additional power supply. Numato Lab USBPOWRL004
Cap for Xbee and Arduino. It has been designed for wireless sensor networks such as WiFi, Bluetooth 2.0 / 4.0 and Zigbee. DFRobot DFR0015
Quad DC Motor Driver Shield is an Arduino compatible DC motor driver that allows you to control 4 DC motors with a voltage between 2.5 ... 13.5V and up to 1.2A. DFRobot DRI0039
Female-female cable, 10 cm long, with JST-SH 6-pin plug on both sides. Suitable for micro DC motor encoders with gear. Pololu 4765
Inox PCTG filament with a diameter of 1.75 mm. 0.75 kg of filament is wound on the spool. Fiberlogy PCTG Inox
Station with two separate panels for a 75W (200-480 deg. C) soldering gun and hotair (100-480 deg. C).
Onyx PCTG filament with a diameter of 1.75 mm. 0.75 kg of filament is wound on the spool. Fiberlogy PCTG Onyx
O.MG Adapter Basic – advanced USB-C adapter with a hidden implant for security testing. O.MG Adapter Basic Black
W25Q128JV flash memory module with 128 Mbit (16 MB) capacity. It supports communication via SPI, Dual or Quad SPI interface. Waveshare W25QXX DataFlash Board
8 Mpx camera module with IMX219 sensor. The camera is intended for use as a replacement on the RPI Camera Board V2. ArduCAM B0180
Module with a stepper motor driver based on the DRV8825 system. allows the bipolar motor to be supplied with current up to 1.5 A per phase, without the use of a heat sink. The system can be supplied with voltage up to 45 V. Pololu 2987
Module with BDS/GNSS AT6558 receiver. It can receive data from six location systems simultaneously: GPS, GLONASS, Galileo, QZSS, SBAS and BeiDou. It communicates via the UART interface. DFRobot TEL0132
Module with BME688 chip, microphone and LTR-559 light intensity. Equipped with a display, it is dedicated to the Raspberry Pi Pico/Pico W. Pimoroni PIM635
This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller’s analog-to-digital converter. Each breakout comes fully assembled and works from 2.7V up to 5.5V. BOB-12758
Natural PLA Mineral filament with a diameter of 1.75 mm. 0.85 kg of filament is wound on the spool. Fiberlogy PLA Mineral Natural