Best sellers

Base board for Raspberry Pi CM4 modules. It integrates the function of an uninterruptible power supply, PoE circuit, it is equipped with connectors for all available interfaces, in addition, there is an RTC system on the board and a fan connector. Waveshare Compute Module 4 PoE Board

Integrated capacitive fingerprint sensor communicating with the external system via the UART interface. The module has a rectangular-shaped sensor field and takes a fingerprint image with a resolution of 160x160 pixels (508dpi). Waveshare UART Fingerprint Sensor (E)

Ethernet transceiver module based on LAN8720 chip. It communicates via the RMII interface. Waveshare LAN8720 ETH Board

DTMF module (two-tone multi-frequency dialing) dedicated to Arduino. It allows you to add the tone signaling function used in telephones for dialing. DFRobot DFR0308

The A-Cute Car is an FPGA-based three-wheeled robotic car kit. This car can provide higher operation performance than the MCU based robotic car, because the FPGA provides more powerful computing power than the MCU. P0467

Hermetic casing ZP90.60.40 light bottom with ears - colorless top with a flooded gasket and brass PC sleeves

Power cord with a built-in Power Delivery (PD) trigger with a working voltage of 12 V. Has a USB type C connector and a DC plug 5.5x2.5 mm. Length 1.2 m

Module with 16 relays with a maximum switching current of 7 A. It communicates via the USB interface. Numato Lab RL160001

DC motor with an offset output shaft gear. Equipped with a magnetic encoder. Waveshare DCGM-3865-12V-EN-240RPM

Enclosure designed for RM500x/RM502x 5G HAT LTE-A modules for Raspberry Pi single-board computers. Waveshare PI4-CASE-4G-5G-M.2

Programmable standard 30 kg*cm servo controlled by UART interface. It can work in the rotation angle control mode or in the continuous operation mode. Waveshare ST3215 Servo

Module with 64 relays and 8 GPIO pins and 6 analog inputs. It communicates via the RS485, USB or Ethernet interface and supports the Modbus RTU/TCP protocol. Numato Lab NLRM1003-A

Development board with Xilinx Artix 7 chip equipped with M.2 connector. It offers a PCIe Gen2 interface and DDR3 2 Gb memory. Numato Lab NLFX1006

Enclosure dedicated to modules with 4 relays by Numato Lab. Numato Lab USBPOWRL004EN

Evaluation board with a Raspberry Pi RP2040 microcontroller and a TCP/IP W5500 controller. WIZnet W5500-EVB-PICO

A 3-port HUB module with a USB 2.0 interface with an RJ45 connector designed to work with the Raspberry Pi minicomputer. Waveshare ETH/USB HUB HAT

7-segment LED display, 1 digit 9.90mm, ultra red (630nm), 24 mcd (10mA), common cathode, Pb-free. LED1-AS-B-03911AMR

Module with 9-axis IMU ICM-20948 sensor (3-axis accelerometer, gyroscope and magnetometer and DMP) and BMP280 pressure sensor. Communication via I2C. Waveshare 10 DOF IMU Sensor (D)

Module with digital barometer BMP388. It enables pressure measurement in the range from 300 to 1250 hPa and communicates via I2C or SPI. Waveshare BMP388 Barometric Pressure Sensor

Adapter with 40-pin RPi socket and CM3 SODIMM connector. It allows you to connect the Raspberry Pi Zero 2 W minicomputer to the base boards dedicated to CM3 modules. Waveshare Zero-to-CM3-Adapter