

WRL-13019 BLE Mate 2
Description:
This is the SparkFun BLE Mate 2, an efficient and reliable Bluetooth 4.0 development board. The BLE Mate 2 closely resembles a breakout board, in that nearly every pin on the on-board BC118 module is made available to access. This board is actually a close cousin to our Gold and Silver Bluetooth Mates and functions in a very similar way but, as the name implies, operates as Bluetooth Low Energy instead of Bluetooth 2.0.
The BLE Mate 2 offers a six-pin header on the end opposite the BC118 module which is used as a “host” serial pinout, the same as that on the FTDI Basic boards, which allows the BLE Mate 2 to be connected directly to any device with a matching header, such as the SparkFun Arduino Pro and Pro Mini. Coupled with the FTDI SmartBasic, you can even develop your code without having to swap cables! The board has built-in level translation, so it can be used with boards of higher voltage than the 3.3V default used by the BC118.
Each BLE Mate 2 offers BC118 module that is capable of accepting and transmitting via the UART at 9600 bps (default) with a frequency band of 2,402 MHz to 2,480 MHz.
The SparkFun BLE Mate 2 only supports Bluetooth 4.0; it won’t connect to older devices. It’s also worth noting that BLE does not support a Serial Port Protocol as older versions of Bluetooth did; that makes interoperability between BLE dongles, devices, and modules harder than with Bluetooth Classic.
Features:
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Expander (shield) compatible with Arduino and NUCLEO (STM32) systems, equipped with a Bluetooth 4.1 (BLE) radio module from the SPBTLE-RF family
Overlay module for Raspberry Pi with GSM, GPRS, GNSS and Bluetooth
An efficient Bluetooth 4.0 module that ensures excellent operating parameters and significantly increases the efficiency of wireless communication. It is based on the popular Nordic BLE 4.0 nRF51822 microcontroller, which guarantees both performance and low power consumption. It has a built-in Bluetooth stack and is controlled via the UART interface using AT commands. WT51822-S4AT
HC-08 is a module operating in the Bluetooth Low Energy 4.0 standard. The system has a built-in antenna and small dimensions, and thanks to edge joints it can be surface soldered. The module is configured via AT commands
Powerful, generic Wi-Fi+BT+BLE MCU modules that target a wide variety of applications, ranging from low-power sensor networks to the most demanding tasks, such as voice encoding, music streaming and MP3 decoding. Espressif ESP32-WROOM-32E 32MBit (4MB)
Bluetooth 4.0 dongle as a USB adapter. Works with bluetooth devices such as speakers, headsets, smartphones, tablets, keyboards, mice, printers, projectors etc.
Diagnostic interface for wireless diagnostics of cars with OBD2 system. The device uses the popular 16-pin connector and is equipped with a Bluetooth 3.0 module. Vgate iCar2 BT3.0 Orange
Development board with LoRa Semtech SX1262 module and Apollo 3 Bluetooth 5 integrated in the NM180100 chip. It supports the 868 MHz and 915 MHz bands and Bluetooth Low Energy. It is compatible with the Qwicc system. SparkFun 17506
No product available!
Bluetooth module v2.0 + EDR (master / slave), controlled by AT + commands with built-in antenna.
No product available!
Low Energy Bluetooth adapter module with 2x4 pin 2.54mm connector, extra / high. RS232 allows communication with BLE devices
Adafruit 2269 - Bluefruit LE Sniffer - Bluetooth Low Energy (BLE 4.0) - nRF51822 - v1.0
Bluetooth 4.0 BLE module powered with 3.3V voltage based on SOC TI CC2541 (On Chip). The module has a range of up to 10m and communicates via the UART interface.
KAmodBT-HC05 is a Bluetooth module configured via AT commands. It has integrated LEDs indicating operating mode and connection status with the paired device, as well as a logic level translator on UART lines. KAmodBT-HC05
Integrated circuit, combining Wi-Fi functionality and Bluetooth 4.2 BLE. Integrated 32-bit dual-core Xtensa LX6 processor, 448kB ROM, 520kB SRAM. ESP32 allows you to work with many interfaces, including SPI, I2C, UART, CAN, ETH, IR and can be supplied with 2.2V-3.6V. The system has a QFN48 (5x5mm) housing. ESP32-D0WD
Expansion board with BlueNRG-M0 module compatible with Bluetooth v4.2. It is compatible with the ST morpho connector system (unmounted) and Arduino UNO R3. Communication with the module is via the SPI interface. STMicroelectronics X-NUCLEO-IDB05A2
WRL-13019