- Out-of-Stock
Dagu Wild Thumper 4WD chassis, silver, 34:1
ID: 195989
Off-road Dagu Wild Thumper 4WD chassis in silver, complete with wheels with a diameter of 120 mm and motors with a 34:1 gearbox. The chassis is made of aluminum sheet, holes with a diameter of 4 mm spaced every 10 mm allow the installation of the controller and accessories. Pololu 1564
Description
Durable, all-terrain chassis with 4-wheel drive from Dagu Electronics. It has been designed to navigate rough terrain and steep grades, making it the perfect platform for any robot that needs to perform tasks in a harsh environment. The design is equipped with four DC motors with brass brushes and 34:1 steel gears that drive large wheels with a diameter of 120 mm. The unique 'super-twist' suspension system keeps each wheel in contact with the ground, ensuring maximum traction even when driving on uneven or bumpy surfaces. The suspension can be adapted to different loads and conditions. The housing is made of corrosion-resistant 2mm anodized aluminum plate, all nuts, bolts and screws are stainless steel, and the brass mounts and suspension springs are nickel-plated. At 7.2 volts, the chassis reaches a top speed of around 7 km / h, and each engine has a torque of around 5 kg-cm.
The aluminum chassis plate has 4 mm holes spaced every 10 mm for easy installation of control electronics, sensors and additional equipment. The baffle in the chassis is designed to hold the 7.2V sub-C batteries that are commonly used in RC cars. These compartments hold two such batteries. The inside of the case also includes convenient screw terminals for connecting the battery leads and engine controller.
Dagu Wild Thumper is a chassis with a differential drive, which means that turning is done by driving the motors on both sides of the platform at different speeds. The three motors on each side of the robot are connected in parallel, so only two control channels are needed to run the landing gear. The motors are designed for a maximum rated operating voltage of 7.2 V (minimum 2 V), with a maximum current consumption of 6.6 A.
Features
- Gear ratio of motors: 34:1
- Ground clearance: 60 mm
- Maximum recommended load capacity: 5 kg
- Recommended motor voltage: 2 V to 7.5 V
- Maximum current at 7.2 V: 6.6 A per motor
- Idle current at 7.2 V: 420 mA per motor
- No load output shaft speed at 7.2V: 350 rpm
- Torque at 7.2 volts: 5 kg-cm per motor
- Dimensions: 280 x 300 x 130 mm
- Weight: 1.9 kg
195989
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 V operating range and are efficient enough to deliver a continuous 18 A without a heat sink.
zł288.26
24h
Available quantity: 1
Available
Pololu G2 18v15 High Power is a miniature DC motor controller. Power supply for the controller: 6.5 ... 30 V. Current efficiency of the module: 15 A. The module has protection against back voltage and overvoltages. Pololu 1362
zł500.01
Delivery date unknown
No product available!
Pololu G2 18v15 High Power is a miniature DC motor controller. Power supply for the controller: 6.5 ... 30 V. Current efficiency of the module: 15 A. The module has protection against back voltage and overvoltages. Pololu 1363
zł551.54
Delivery date unknown
No product available!
Other products in the same category (16)
No product available!
No product available!
Assembled thermometer with a green LED display that allows temperature measurement from -55 ° C to + 125 ° C. AVT3122 C
Retired
No product available!
Round and round and back to where it\'s all begun… Take a trip to your childhood memories with Ugears beautiful nostalgic model, the Carousel.
This outstanding model is a Ugears look at the classic merry-go-round implemented in top-quality wood, the familiar and beloved fairground ride is presented with highly-detailed design. UGears 70129
Retired
No product available!
Xilinx Kintex®-7 XC7K325T-1FFG676 FPGA. 6015-410-001-KIT
Retired
No product available!
No product available!
A universal IR remote designed for NanoPi M1, powered by two AAA batteries. FriendlyELEC RC-100
Retired
No product available!
No product available!
No product available!
Flexible Qwiic cord with a length of 165 mm. On one side it is terminated with a Qwiic female connector, and on the other side with single goldpin female connectors. SparkFun CAB-22726
Retired
No product available!
No product available!
David Munoz, Frantz Bouchereau Lara, Cesar Vargas, Rogerio Enriquez-Caldera
Delivery date unknown
No product available!
No product available!
The computer with Intel Celeron N4100, has 4GB RAM and 32GB eMMC. It has Wi-Fi, Bluetooth 4.0, Ethernet, as well as Intel HD Graphics. Has support for Windows 10 and Linux. Version with activated Windows 10 Pro. DFRobot DFR0544
Retired
No product available!
No product available!
The UM7 orientation sensor from CH Robotics is an Attitude and Heading Reference System (AHRS) that contains a three-axis accelerometer, rate gyro, and magnetometer. It combines this data using an Extended Kalman Filter to produce attitude and heading estimates. Pololu - 2741
Retired
No product available!
Off-road Dagu Wild Thumper 4WD chassis in silver, complete with wheels with a diameter of 120 mm and motors with a 34:1 gearbox. The chassis is made of aluminum sheet, holes with a diameter of 4 mm spaced every 10 mm allow the installation of the controller and accessories. Pololu 1564