SparkFun Serial Basic Breakout - CH340G
ID: 564247
5906623417827
zł51.66
Tax included
zł42.00 tax excl.
Easy-to-use USB-to-Serial adapter based on the CH340G IC from WCH; works with 5V and 3.3V systems and should auto install on most operating systems without the need for additional drivers; uses the CH340G IC to quickly and easily convert serial signals to USB. DEV-14050
Description
The SparkFun Serial Basic Breakout is an easy-to-use USB-to-Serial adapter based on the CH340G IC from WCH. It works with 5V and 3.3V systems and should auto install on most operating systems without the need for additional drivers. The Serial Basic uses the CH340G IC to quickly and easily convert serial signals to USB. It’s a great lower-cost alternative to the extremely popular FTDI Basic.
The pinout of the Serial Basic mimics the common DTR/RX/TX/VCC/CTS/GND pinout found on hundreds of FTDI-to-USB derivatives. It can also be used as a general serial device for debugging (such as with a GPS module). There is a jumper on the rear of the board that controls the output voltage on the VCC pin. By default, the board outputs 3.3V and has 3.3V signals. Changing this jumper to 5V will cause the board to output 5V on the VCC pin with 5V signals.
564247
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
Easy-to-use USB-to-Serial adapter based on the CH340G IC from WCH; works with 5V and 3.3V systems and should auto install on most operating systems without the need for additional drivers; uses the CH340G IC to quickly and easily convert serial signals to USB. DEV-14050
zł51.66
24h
Available quantity: 2
Available
The CY7C65213 USB to UART serial breakout is designed to provide users with a means to access all available I/O pins on the IC, and to provide a 6-pin UART header that is compatible with other SparkFun breakout boards. This breakout has a microUSB connector and other support circuitry to get the IC quickly up and running. BOB-13830
zł82.40
24h
Available quantity: 1
Available
WIFI-LPT100 Eval Kit module enables UART data transmission via WiFi, ultra low power consumption, encrypted communication
zł110.76
4 weeks
No product available!
USB - UART converter based on the PL2303 chip
zł9.00
24h
Available quantity: 19
Available
CP2102 USB to UART Module, USB mini connector
zł20.66
4 weeks
No product available!
UART - RS232 converter with DB9 socket. Waveshare rs232-board
zł12.80
4 weeks
No product available!
Overlay module for Raspberry Pi with GSM, GPRS, GNSS and Bluetooth
zł124.62
24h
Available quantity: 7
Available
Xbee USB adapter based on the FTDI chip. Intended for configuring Xbee modules. Thanks to the female goldpin connector, it can be used as an FTDI programmer for Arduino FIO / pro / mini / lilypad. DFRobot DFR0050
zł81.45
24h
Available quantity: 2
Available
The UART-USB converter built on the FTDI FT232RL chip. Compatible with 3.3V and 5V voltages. DFRobot DFR0065
zł54.07
24h
Available quantity: 1
Available
USB - UART converter based on the FT232RL chip. Compatible with voltages of 3.3 V and 5 V, it is equipped with a microUSB connector. Cytron UC00A
zł38.92
24h
Available quantity: 1
Available
USB - UART TTL converter based on the FT232RL chip, the module is equipped with a miniUSB socket. Works with 3.3V or 5V voltage levels.
zł14.58
24h
Available quantity: 17
Available
USB port isolator based on the ADUM3160 chip. The device has a rated insulation voltage of 1500V. The isolator is powered from the USB port.
zł70.37
4 weeks
No product available!
A small USB-UART TTL converter module based on the CH340 system with a USB type A connector. Designed for the ESP-01 and ESP-01S modules
zł5.29
24h
Available quantity: 10
Available
UART-RS232 converter module. The board was equipped with a Grove and DB9 connector. Seeed Studio 103020192
zł38.38
24h
Available quantity: 1
Available
USB adapter designed for XBee modules. It can be connected to a computer with a USB cable and used with the X-CTU software to configure the XBee. DFRobot DFR0174
zł97.48
24h
Available quantity: 1
Available
RS232 - UART converter module based on the MAX3232 chip. There is a DB9 connector on the board and a 4-pin connector with a 2.54 mm pitch
zł4.51
24h
Available quantity: 16
Available
Easy-to-use USB-to-Serial adapter based on the CH340G IC from WCH; works with 5V and 3.3V systems and should auto install on most operating systems without the need for additional drivers; uses the CH340G IC to quickly and easily convert serial signals to USB. DEV-14050