zł27.89 tax excl.
KAmod RS232S-mini is a miniature RS232 to TTL converter with a female DB9 connector, 2.54 mm goldpin pins, operating at 3-5.5 V, supporting all RS232 signals, based on the MAX3238/SP3238 chip, offering ESD protection up to 15 kV and corresponding to a DCE/Modem device
KAmod RS232S-mini is a miniature RS232 to TTL converter that contains all RS232 interface signals: RXD, TXD, DTR, DSR, RTS, CTS, DCD and RI. The signal conversion direction is assigned in such a way that it corresponds to a DCE/Modem device (slave device, TXD is RS232 signal input, RXD is RS232 signal output). The converter has a typical female DB9 connector on the RS232 side and 2.54 mm goldpins on the TTL side. It can operate at a supply voltage of 3...5.5 V.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The cable is easiest way ever to connect to your microcontroller/Raspberry Pi/WiFi router serial console port. The power pin provides the 5V @ 500mA direct from the USB port and the RX/TX pins are 3.3V level for interfacing with the most common 3.3V logic level chipsets. Adafruit 954
Easy-to-use USB-to-Serial adapter based on the CH340G IC from WCH; works with 5V and 3.3V systems and should auto install on most operating systems without the need for additional drivers; uses the CH340G IC to quickly and easily convert serial signals to USB. DEV-14050
The CY7C65213 USB to UART serial breakout is designed to provide users with a means to access all available I/O pins on the IC, and to provide a 6-pin UART header that is compatible with other SparkFun breakout boards. This breakout has a microUSB connector and other support circuitry to get the IC quickly up and running. BOB-13830
WIFI-LPT100 Eval Kit module enables UART data transmission via WiFi, ultra low power consumption, encrypted communication
No product available!
USB - UART converter based on the PL2303 chip
UART - RS232 converter with DB9 socket. Waveshare rs232-board
Overlay module for Raspberry Pi with GSM, GPRS, GNSS and Bluetooth
Xbee USB adapter based on the FTDI chip. Intended for configuring Xbee modules. Thanks to the female goldpin connector, it can be used as an FTDI programmer for Arduino FIO / pro / mini / lilypad. DFRobot DFR0050
The UART-USB converter built on the FTDI FT232RL chip. Compatible with 3.3V and 5V voltages. DFRobot DFR0065
USB - UART converter based on the FT232RL chip. Compatible with voltages of 3.3 V and 5 V, it is equipped with a microUSB connector. Cytron UC00A
USB - UART TTL converter based on the FT232RL chip, the module is equipped with a miniUSB socket. Works with 3.3V or 5V voltage levels.
No product available!
USB port isolator based on the ADUM3160 chip. The device has a rated insulation voltage of 1500V. The isolator is powered from the USB port.
No product available!
A small USB-UART TTL converter module based on the CH340 system with a USB type A connector. Designed for the ESP-01 and ESP-01S modules
UART-RS232 converter module. The board was equipped with a Grove and DB9 connector. Seeed Studio 103020192
KAmod RS232S-mini is a miniature RS232 to TTL converter with a female DB9 connector, 2.54 mm goldpin pins, operating at 3-5.5 V, supporting all RS232 signals, based on the MAX3238/SP3238 chip, offering ESD protection up to 15 kV and corresponding to a DCE/Modem device