Cytron Maker Drive is a two-channel DC motor driver. It can be supplied with a voltage in the range of 2.5-9.5 V. The module can supply current up to 1 A per channel in continuous operation or 1.5 A at peak. It has protection against reverse polarity of power supply and 4 buttons and 4 LEDs allowing for quick test of connected drives. The module can also be used as a stepper motor driver. The module is also equipped with an embedded voltage regulator.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
The long-awaited Raspberry Pi 4 model B with the SoC Broadcom BCM2711 SoC (4 x Cortex-A72) running at 1.8 GHz, 4 GB LPDDR4 RAM and the Broadcom VideoCore VI graphics chip
Two-channel DC motor driver with an operating voltage from 7 to 35 V and a maximum continuous current of 30 A. It can be controlled by an analog signal, PWM, UART, RC signal or by means of built-in buttons. Cytron MDDS30
Two-channel driver for DC motors with an operating voltage from 7 to 35 V and a continuous current up to 10 A. It can be controlled by an analog signal, PWM, UART, RC or by means of built-in buttons. Cytron MDDS10
DC motor driver with a working voltage from 5 to 30 V and a maximum continuous current of 13 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MD10C
Direct current motor driver (DC) with a working voltage from 5 to 30 V and a maximum continuous current of 30 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MD30C
No product available!
HAT with two-channel DC motor driver for Raspberry Pi. It has an operating voltage from 6 to 24 V and a continuous current of up to 10 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron HAT-MDD10
No product available!
Two-channel driver of direct current (DC) motors with an operating voltage from 5 to 30 V and a maximum continuous current of 10 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MDD10A
Two-channel driver of direct current (DC) motors with an operating voltage from 4 to 16 V and a maximum continuous current of 3 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MDD3A
No product available!
Direct current motor driver (DC) with a working voltage from 7 to 58 V and a maximum continuous current of 25 A. It can be controlled by a PWM signal, a potentiometer or by means of built-in buttons. Cytron MD25HV
Shield with dual-channel DC motor driver for Arduino. It has an operating voltage from 7 to 30 V and a continuous current of up to 10 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron SHIELD-MDD10
No product available!
Module with 2-channel DC motor driver. It allows you to control the drive with a supply voltage from 3 to 11 V and a current of 1.2 A (1.5 A instantaneous). I2C communication. SparkFun ROB-15451
No product available!
Module with 2-channel driver for DC motors L298P. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 105020093
Module with TB6612FNG DC motors dual driver. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 108020103
Module with two DRV8830 DC motor drivers. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 105020010
No product available!
The module with the DRV8830 DC motor controller with a maximum current of 1 A. The board is equipped with a screw connector and communicates via the I2C interface. Pimoroni PIM479
Two-channel DC motor driver powered with the voltage from 2.5 to 12 V with a maximum continuous current of 0.8 A per channel. It can control a bipolar stepper motor
No product available!
Two-channel driver of direct current (DC) motors with an operating voltage from 6 to 30 V and a maximum continuous current of 20 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MDD20A
No product available!
Dual DC motor controller with voltage from 2.5 to 9.5V with 1A continuous current per channel. Has an embedded voltage regulator. Cytron Maker Drive