![Main view Main view](https://kamami.pl/73860-large_default/nano-power-timer-module-with-counter-tpl5110.jpg)
![Main view Main view](https://kamami.pl/73860-large_default/nano-power-timer-module-with-counter-tpl5110.jpg)
zł25.68 tax excl.
TPL5110 external counter module to turn on a project after a set time and save energy. The TPL5110's delay is configurable with resistors ranging from 100 ms to two hours. SparkFun PRT-15353
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
Module with an external counter TPL5110, which allows you to turn on the project after a set time and save energy if the device does not need to run all the time. It allows, for example, after reading measurements from sensors, sending data and storing them in the recorder, to turn off the power and then turn it on again, for example, after 1h.
The TPL5110's delay is configurable via resistors. Operation is facilitated by a six-way DIP switch, which allows you to select one of five pre-installed resistors. A sixth switch is attached to a pad that allows you to add your own PTH (or SMD) resistor. The delays associated with the pre-installed settings are labeled on the bottom of the board for quick configuration. In addition, more than one switch can be selected to connect resistors in parallel (up to 26 options, not including a custom resistor).
The Nano Power Timer supports voltages from 1.8 V to 5.5 V and currents up to 1.1 A. Timing configuration options range from 100 ms to two hours (preconfigured settings from 30s to 2h). There is a button on the board that will allow the user to quickly override the delay, so you can turn on your project at any time. Full documentation and usage examples are available on the product page.
Li-Po battery 3.7V / 220mAh. Connector + JST-BEC 2,54, 2 pins, PCM protection, cable length 150mm. Akyga LP402036
Li-Po battery with a rated voltage of 3.7 V and a capacity of 400 mAh, equipped with a PCM protection and a 2.5 JST-RCY connector and socket. Akyga LP403035
A single-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with soldered connectors. Pololu 5076
The trigger module is designed for chargers PD 2.0 and PD 3.0. It is equipped with a USB type C input and a USB type A output. It enables powering devices with 9 V or 12 V and testing chargers. PDC005
USB - UART converter based on the FT232RL chip. Compatible with voltages of 3.3 V and 5 V, has been equipped with a USB type C connector. Waveshare FT232 USB UART Board (Type C)
The module with the DRV8830 DC motor controller with a maximum current of 1 A. The board is equipped with a screw connector and communicates via the I2C interface. Pimoroni PIM479
Real time clock (RTC) module PCF8523. It communicates via the I2C interface. Adafruit 3295
A stereo tube preamplifier based on 6K4 tubes. Designed for use with active speakers or an additional amplifier and passive speakers. FX-AUDIO Tube-03 SUCA-AUDIO Tube-T1
No product available!
TF Mini LiDAR is a one-way rangefinder that is based on ToF (Time of Flight) technology. It consists of high quality optical and electrical devices that provide stability, high sensitivity and precision. Sparkfun SEN-14786
No product available!
An audio module with a DAC converter and a stereo amplifier designed to work with the Raspberry Pi. Adafruit 3346
DC motor driver that allows you to control the movement of three drives using the I2C interface. Pololu 5035
Set of two magnetic encoders for use with micro motors. Side mounting, set of 2. Pimoroni PIM605
USB - RS232 adapter equipped with a USB type A connector and an RS232 connector in the DB9 male standard. It uses the original FTDI FT232RL chip, which guarantees a reliable connection between a variety of devices. Waveshare USB-TO-RS232-Male-Cable
Gravity: I2C 3.7V Li Battery Fuel Gauge is a module for monitoring the parameters of the Li-ion battery allowing for precise measurement of the flow of charge to / from a 1-source source with an input voltage of 2.5-4.2V. DFRobot DFR0563
Gravity module designed based on the GP8501 system. It is a two-channel DAC (analog-to-digital) converter with PWM communication that offers an output signal with 8-bit resolution and 0.5% accuracy. It allows you to generate analog signals with a voltage range from 0 to 2.5 V or from 0 to VCC. DFRobot DFR1037
A stereo tube preamplifier based on 6K4 tubes. Designed for use with active speakers or an additional amplifier and passive speakers. SUCA-AUDIO TUBE-T1
No product available!
No product available!
TPL5110 external counter module to turn on a project after a set time and save energy. The TPL5110's delay is configurable with resistors ranging from 100 ms to two hours. SparkFun PRT-15353