Development board D1 Mini V3 WIFI ESP8266

WiFi 802.11 b/g/n module with ESP8266 system, 16 terminals are available with a 2 mm pitch with the possibility of soldering gold pins, there are 9 GPIO lines and 1 ADC line on the connector. Built-in ceramic antenna and U.FL antenna connector. ESP-07

Adafruit Feather HUZZAH ESP8266 is a new development board from Adafruit with a built-in WiFi module ESP8266. Processor frequency: 80 MHz, USB-serial TTL CP2104 converter, Li-Pol battery charger. Adafruit 2821

Wi-Fi module based on the ESP8266 system - simplicity of use (communication through UART, supports AT commands), 3.3V power supply, support for WPA / WPA2 encryption - these features make the EPS8266 module applicable anywhere, where reliable and effective data transmission. The module is not equipped with an antenna, it should be attached using the U.FL connector. ESP-05

WiFi module based on ESP8266. It has an embedded antenna and 0.96 "OLED display. The module can be programmed in Lua (under NodeMCU firmware control) or in the Arduino IDE. Provides 12 GPIO lines.

A set with environmental sensors that allows you to measure air pollution and noise and visualize data on a dedicated platform. Seeed Studio 102110258

Development board D1 Mini Pro with WiFi ESP8266 module and 16 MB Flash memory, equipped with ceramic antenna and external antenna connector. The module can be programmed from the Arduino IDE level. WeMos D1 Mini Pro

WiFi module based on ESP8266. The module has a built-in antenna and USB-UART converter. The module can be programmed in Lua (under the control of the NodeMCU firmware) or in the Arduino environment. 10 GPIO lines are available which each can be configured to work as PWM, I2C.

The module is based on the ESP8266EX chip. Thanks to the support of the 802.11 b/g/n standard, it enables wireless communication with WiFi networks, which allows for Internet access and data exchange. It is programmed via the USB Type-C connector using Arduino, MicroPython or NodeMCU. WeMos D1 Mini Type-C

BMP180 temperature / pressure sensor module compatible with WeMos D1 mini board.

ESP-PROG is an advanced tool for programming and debugging Espressif microcontrollers such as ESP32, ESP32-C3, ESP32-S2, ESP32-S3 and ESP8266. With the built-in FT2232HL USB bridge, ESP-PROG converts the USB 2.0 interface to serial and parallel interfaces, offering functions of automatic firmware download, serial communication and online debugging via JTAG

WiFi 802.11 b/g/n module with ESP8266 system, they have 22 edge terminals with 2 mm raster with the possibility of soldered gold connectors, 9 GPIO lines and 1 ADC line on the connector. Built-in PCB antenna. ESP-12E

Development board with ESP8266 microcontroller with built-in Wi-Fi communication. The system is clocked at 80 MHz and powered by 3.3 V. It includes a Tensillica core and a full Wi-Fi stack. Adafruit 3046

Development board with RP2040 and ESP-12E microcontroller. Equipped with 0.91" OLED display. SB Components 24186

ESP8266 based Arduino board for ArduCAM mini camera modules while keeping the same form of factors and pinout as the standard Arduino UNO R3 board. ArduCAM B0082

Development kit with WiFi / Bluetooth module ESP8266 and 0.96 "OLED display.

LoLin NodeMCU V3 is a board with ESP8266 (ESP12E). The ESP8266 system provides WiFi connectivity (802.11 b / g / n). The USB-UART converter (CH340G chip) is located on the board. The module can be programmed in Lua (under the control of the NodeMCU firmware) or in the Arduino environment. There are 10 GPIO lines available.