

A sensor that detects the concentration of ammonia. It is equipped with a factory calibrated probe and allows you to quickly and accurately measure the concentration of gas in the environment. The probe used is resistant to interference, offers high stability and sensitivity as well as a service life of up to two years. The sensor communicates via the I2C interface, UART or analog output, has 32 modifiable I2C addresses, an integrated temperature compensation algorithm and a threshold alarm function. It can be widely used for the detection of ammonia in industry and environmental protection. Full documentation and examples of use are available on the product page.
Data sheet
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
Gravity: Formaldehyde (HCHO) Sensor is a module for measuring the concentration of formaldehyde (methane) in the air. It can be supplied with voltage in the range of 3.3 ... 6V. DFRobot SEN0231
A set of 10 cables, 30 cm long, compliant with the Gravity standard. DFRobot FIT0513
A sensor that detects the concentration of hydrogen fluoride. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0475
No product available!
Gravity: Formaldehyde (HCHO) Sensor is a module for measuring the concentration of formaldehyde (methane) in the air. It can be supplied with voltage in the range of 3.3 ... 6V. DFRobot SEN0231
The sensor is designed for indoor air quality testing. The main gas detected is carbon monoxide, alcohol, acetone, thinner, formaldehyde and other slightly toxic gases. It is compatible with 5V and 3.3V power supply. Seeed Studio 101020078
Module with nitrogen dioxide sensor made in MEMS technology. It allows gas detection in the range of 0.1 to 10 ppm and has an analog output. DFRobot SEN0574
A module for the detection of gases and vapors of alcohols, including ethanol.
Air quality sensor module based on the SGP40 system. It communicates via the I2C interface. DFRobot SEN0392
Pololu MQ Gas Sensor Carrier
Module with a sensor of formaldehyde (methanal) concentration in the air. The board is equipped with a Grove connector and communicates via the I2C or UART interface. Seeed Studio 101020972
No product available!
A sensor used to detect pollutants in the air by measuring gases such as hydrogen, ethanol and carbon monoxide. It is used in various areas, such as the food industry, chemical industry, air quality control in laboratories and environmental monitoring. Figaro TGS2600
MH-Z16 carbon dioxide sensor with Grove connector. It communicates via the UART interface. Seeed Studio 101020067
Adapter for MQ gas sensor with potentiometer for analog signal calibration. MOD 72
Module with an analog sensor of carbon monoxide and combustible gases (methane, propane) MQ9. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0134
Module with the MQ3 analog alcohol sensor. It enables gas detection and construction of a simple breathalyzer. The module is powered by 5 V and has an analog output. DFRobot SEN0128
Sensor that detects the concentration of chlorine. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0468
No product available!
Module with a digital gas sensor MiCS-4514. It allows you to measure the concentration of CO, C2H5OH, H2, NO2, NH3 and communicates via the I2C interface. DFRobot SEN0377
No product available!
Module with four gas sensors that allow the detection of CO, NO2, alcohol and volatile organic compounds (VOC). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020820
Module with a gas concentration sensor MQ9, which enables the detection of carbon monoxide and combustible gases (methane, propane). The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020045
A sensor that detects the concentration of ammonia. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0469