Grove I2C Thermocouple Amplifier
ID: 583179
5906623415571
zł80.27
Tax included
zł65.26 tax excl.
The module with the MCP9600 amplifier is designed to work with a thermocouple. The board is equipped with a Grove connector and communicates via I2C. Seeed Studio 101020594
Description
The module with the MCP9600 amplifier is designed to work with a thermocouple. There are four pads on the bottom that allow you to read the alarms of exceeding the temperature generated by the amplifier. The board is equipped with a Grove connector, so it can be used with the Base Shield V2 and Arduino extension. The module communicates via the I2C interface and is supplied with the voltage of 3.3 V or 5 V. It will be used in projects requiring measurement in a wide temperature range. Full documentation of the module with examples of use is available on the product page.
Features
- Works with K, J, T, N, S, E, B and R thermocouples
- Measurement accuracy: 1.5°C
- Measurement resolution: 0.0625°C
- Integrated cold junction compensation
- 4 programmable alarm outputs
- Digital filter and programmable hysteresis
- Low power mode
- Interface: I2C
- I2C address: 0x60 (default) or 0x67
- Supply voltage: 3.3 V or 5 V
- Dimensions: 20 x 40 x 18mm
- Weight: 11 g
Kit contains
- Grove I2C Thermocouple Amplifier module
- Grove cable
583179
Data sheet
- Interface
- I2C
- Type of sensor
- inny
- Power supply voltage
- 3,3 - 5 V
- Sensor type
- Thermocouple amplifier
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface
zł53.71
24h
Available quantity: 20
Available
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.42
Delivery date unknown
No product available!
With the help of a thermocouple, it is possible to measure the temperature of the air and the surface. The use of a steel stainless steel tip in a K-type thermocouple allows the temperature to be measured up to 500 ° C. The cord length is approximately 100 centimeters. Adafruit 3245
zł52.21
24h
Available quantity: 7
Available
Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000
zł24.40
24h
Available quantity: 19
Available
Grove module with temperature, humidity and pressure sensor. The board is equipped with a Grove connector and communicates via I2C or SPI. Seeed Studio 101020193
zł92.99
24h
Available quantity: 3
Available
Other products in the same category (16)
I2C-CAN converter using the MCP2551 and MCP2515 systems and the ATmega168PA microcontroller. The module uses the I2C bus and the Grove connector for communication. Seeed Studio 113020111
zł97.10
24h
Available quantity: 4
Available
Module with an IR receiver operating at a frequency of 38 kHz. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020016
zł19.93
24h
Available quantity: 2
Available
LM386 audio amplifier module in a set with a loudspeaker. The board is equipped with a Grove connector and is controlled by a PWM signal. Seeed Studio 101020853
zł57.54
24h
Available quantity: 1
Available
Module with a humidity sensor. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020018
zł17.64
24h
Available quantity: 2
Available
A 4-core cable with a length of 30 cm, both terminated with a Grove plug. Seeed Studio 110990040
zł10.74
4 weeks
No product available!
Module with LoRa transmitter based on RFM95 (SX1276 LoRa®). It works with a frequency of 433 MHz, maximum power up to 100 mW and a power gain of up to + 20dBm. The module has a built-in antenna, but it is possible to connect an external antenna (MHF connector). The module has a connector in accordance with the Grove standard. Seeed studio 113060007
zł84.92
24h
Available quantity: 1
Available
Module with light sensor - LS06-S phototransistor. The board is equipped with a Grove connector and has an analog output. Seeed Studio 101020173
zł21.99
24h
Available quantity: 3
Available
The module with the BS312 PIR sensor, which allows motion detection at a distance from 3.2 to 12 m. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020793
zł22.41
24h
Available quantity: 2
Available
Module for recording sounds, which can store recordings up to 20 seconds. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 107020007
zł37.82
24h
Available quantity: 1
Available
A module with an NFC PN532 transceiver, which supports proximity communication at the frequency of 13.56 MHz. The board is equipped with a Grove connector and communicates via the I2C or UART interface. Seeed Studio 113020006
zł97.67
24h
Available quantity: 5
Available
Module with the alcohol sensor MQ303A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020044
zł43.95
24h
Available quantity: 1
Available
A 4-core cable with a length of 50 cm, both terminated with a Grove plug. Seeed Studio 110990038
zł15.19
4 weeks
No product available!
Module with air quality sensor SGP30. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020512
zł51.89
4 weeks
No product available!
Module with 8 relays SSR G3MC202P with a load up to 2 A. The board is equipped with a Grove connector and communicates via I2C. Seeed Studio 103020136
zł446.91
4 weeks
No product available!
Angled Grove socket for through-hole mounting, 4-pin, pitch 2.0 mm. Set of 10 pieces. Seeed Studio 110990037
zł8.12
4 weeks
No product available!
Module with a button and RGB LED backlight. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 111020049
zł20.91
4 weeks
No product available!
The module with the MCP9600 amplifier is designed to work with a thermocouple. The board is equipped with a Grove connector and communicates via I2C. Seeed Studio 101020594