![COLORCOLOR - color sensor module (TCS3200) with LED backlight COLORCOLOR - color sensor module (TCS3200) with LED backlight](https://kamami.pl/5084-large_default/colorcolor-color-sensor-module-tcs3200-with-led-backlight.jpg)
![COLORCOLOR - color sensor module (TCS3200) with LED backlight COLORCOLOR - color sensor module (TCS3200) with LED backlight](https://kamami.pl/5084-large_default/colorcolor-color-sensor-module-tcs3200-with-led-backlight.jpg)
zł36.50 tax excl.
Module with TCS3200D system - sensor of RGB light components
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
The KAmodCOLOR module was built based on the TAOS semiconductor color sensor TAOS3200D. This system has a matrix with the organization of 8 × 8 photodiodes (16 each with red, green and blue filters and without a filter). It allows you to measure the RGB components of the incident light.
Cables for evaluation boards, set of 10 pcs., blue colour
Cables for evaluation boards, set of 10 pcs., red colour
Cables for evaluation boards, set of 10 pcs., green colour
Cables for evaluation boards, set of 10 pcs., yellow colour
Cables for evaluation boards, set of 10 pcs., white colour
Set of 40 pieces of male-female connection cables, in various colors, 17 cm long. CAB_M-F (Rainbow-40-17)
No product available!
No product available!
KAmodQTR8A is a module with eight photointerrupter sensors KTIR0711S. It allows to detect edge or line. Thanks to the analog outputs, is possible to connect a module to the e.g. comparator. The module can be used in analisze of the floor e.g. by Linefollower vehicles.
Relay output module for Raspberry Pi 4B, Pi 3B+ Pi3B, Pi2, Pi+, Pi minicomputers.
The KAmodPCAL6408 is an 8-bit I/O expander with the PCAL6408A chip by NXP, controlled by the I2C interface.
KAmodMIC_ELECTRET is a module with microphone KPCM6B type. Thanks to embedded amplifier with hundredfold amplification of signal, output voltage can be measurement in microcontroller with using e.g. ADC converter.
KAmodWS2812-1 is a module with WS2812 multicolor LED. Thanks to the embedded controller, LED can be series connected to makes an amazing light effects. KAmodWS2812-1
KAmodPCA9533 is a module with LED driver from NXP. The module allows you to control the brightness of 4 LEDs using programmable PWM signals (with a frequency from 0.591 Hz to 152 Hz). I2C interface. The board is equipped with a Pmod I2C standard connector and a KAMAMI connector
Pressure sensor module with I2C interface (MPL115A2)
KAmodLSM303C is a module with the MEMS LSM303C chip from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows measurement of accelerations and magnetic field values in three axes
Multifunctional expander (shield) for NUCLEO and Arduino equipped with Bluetooth 2.0+EDR (HC-05) interface, MEMS 3DoF LIS35, LED-RGB, joystick and analog STLM20 temperature sensor developed and produced by KAMAMI.
KAmodPCF8883T is a module with capacitive touch sensor PCF8883 from NXP. The module has a probe placed on the PCB and a diode indicating the state of the chip. It enables work in one of three modes.
The KAmodRS module is a reliable RS232-UART converter supporting voltages from 3 V to 5.5 V and enabling data transmission at a speed of up to 250 kbit/s. Thanks to the use of the MAX3232 chip, the module is ideal for a wide range of electronic and microcontroller applications requiring stable and effective serial communication
KAmodMPL3115A2 is a module with an atmospheric pressure sensor MPL3115A2 from NXP. Sensor allows to make a measurement in the range of 200...1100hPa (20...110kPa). Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMPL3115A2
Module with TCS3200D system - sensor of RGB light components