zł124.56 tax excl.
Micsig MSP510 passive oscilloscope probe with a 500 MHz bandwidth and 1:10 attenuation designed for precise high-frequency signal measurements. Compatibility with the BNC standard and compensation adjustment make it a universal tool for laboratories and electronics workshops.
The Micsig MSP510 passive probe is designed for digital and analog oscilloscopes with a BNC input. It enables precise measurement of signals with a bandwidth of up to 500 MHz and a rise time not exceeding 800 ps. The probe provides a 10:1 attenuation ratio and high input impedance of 10 MΩ, which minimizes the probe’s impact on the tested circuit. Equipped with a compensation capacitor of 10.5 pF (adjustable in the range of 4–24 pF), it allows accurate matching to the oscilloscope’s input characteristics. Thanks to the standard BNC connector, the probe is compatible with most oscilloscopes available on the market. A flexible 132 cm cable facilitates maneuvering during measurements, while the low weight (below 53 g) improves work comfort.
Manufacturer
Responsible person
6-wire test leads that allow the oscilloscope to be connected to various components in the engine compartment without stripping or puncturing the insulation and without risking damage to the connectors. Hantek HT306-2.8mm
No product available!
6-wire test leads that allow the oscilloscope to be connected to various components in the engine compartment without stripping or puncturing the insulation and without risking damage to the connectors. Hantek HT306-2.3mm
6-wire test leads that allow the oscilloscope to be connected to various components in the engine compartment without stripping or puncturing the insulation and without risking damage to the connectors. Hantek HT306-1.5mm
6-wire test leads that allow the oscilloscope to be connected to various components in the engine compartment without stripping or puncturing the insulation and without risking damage to the connectors. Hantek HT306-1.0mm
Cable (adapter) of a BNC connector to banana plugs. Allows convenient connection of the device to an oscilloscope, for example. Hantek HT30A
No product available!
Cable (adapter) of a BNC connector to banana plugs. Allows convenient connection of a device to an oscilloscope, for example. BNC Q9
Probe for measuring direct current up to 800 A and alternating current up to 500 A. Operates at 5 kHz and can be connected to an oscilloscope via a BNC connector. Powered via USB. Hantek CC-800
No product available!
High-voltage differential probe. It has good measurement characteristics: a bandwidth of 50 MHz and an operating voltage of up to 1300 V. The probe has two attenuation coefficients: 50X and 500X. Hantek HT8050
High-voltage differential probe. It has good measurement characteristics: a bandwidth of 100 MHz and an operating voltage of up to 1300 V. The probe has two attenuation coefficients: 50X and 500X. Hantek HT8100
No product available!
Universal oscilloscope probe with BNC connector and 10:1 voltage divider. It has a frequency response of 80 MHz and allows measurements with a maximum voltage of up to 600 V. Hantek PP-90
A set of needle probes used for piercing wire insulation. They can be used as pin probes when working with small PCBs or connectors. Hantek HT307
Universal oscilloscope probe with BNC plug and 10:1 voltage divider. It has a frequency range of 60 MHz and allows you to perform measurements with a maximum voltage of up to 600 V.
Oscilloscope probe designed to analyze signals generated by the ignition coil in car engines. It is compatible with most digital oscilloscopes. Hantek HT25COP
Oscilloscope probe designed to analyze signals generated by the ignition coil in car engines. It is compatible with most digital oscilloscopes. Hantek HT20COP
An oscilloscope probe designed to analyze signals generated by the ignition coil in car engines. It is compatible with most digital oscilloscopes. Micsig MS-A-008
Insulated fiber optic probe with a measuring range up to 2500 V. It works in the band up to 100 MHz, it can be connected to the oscilloscope via the BNC connector. Comes with a 10X attenuation tip. MOIP100P
No product available!
Micsig MSP510 passive oscilloscope probe with a 500 MHz bandwidth and 1:10 attenuation designed for precise high-frequency signal measurements. Compatibility with the BNC standard and compensation adjustment make it a universal tool for laboratories and electronics workshops.