Gravity: I2C Voice Recorder - sound recording module
ID: 588817
5906623407279
zł47.26
Tax included
zł38.42 tax excl.
Sound recording module with I2C interface. It can store sounds up to 100 seconds long. DFRobot SEN0197
Description
Sound recording module with Gravity connector. The set is supplied with the voltage from 3.3 to 5 V and can store sounds up to 100 seconds long. After connecting a loudspeaker or headphones, the user can play sounds directly via the module. The recording process can be started by a switch or by sending a command via the I2C interface. The module can be connected to a microcontroller that will trigger the playback of recorded sounds. The board houses an audio amplifier and a potentiometer to adjust the volume level. Full documentation and examples of use are available on the product page.
Features
- Recording time: 10 fragments up to 100 seconds
- Gravity connector
- I2C interface (address from 0x30 to 0x39)
- Jack 3.5mm audio output
- JST PH2.0 speaker audio output
- Supply voltage: 3.3 to 5 V
- Dimensions: 57 x 40 mm
588817
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.42
24h
Available quantity: 106
Available
Available
A set of 10 cables, 30 cm long, compliant with the Gravity standard. DFRobot FIT0513
zł28.41
24h
Available quantity: 4
Available
Other products in the same category (9)
Audio module with WM8960 stereo codec. It allows you to record sounds and play them. Waveshare 15019
zł60.29
24h
Available quantity: 8
Available
Recorder v3.0 is a module that allows you to record and play sounds. The module was based on the ISD9160FI system, it also has a FLASH memory with a capacity of 2 MB, which allows for recording up to 83 seconds long. The set contains a small loudspeaker on which recorded sounds can be played. Seeed studio 107020029
zł60.82
24h
Available quantity: 2
Available
This breakout board, the ultimate companion for the VLSI VS1053B DSP codec chip, can decode a wide variety of audio formats MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM); it can be used to record audio in both PCM (WAV) and compressed Ogg Vorbis. 8 GPIO pins can be used for lighting up small LEDs or reading buttons. Adafruit 1381
zł131.84
24h
Available quantity: 1
Available
The Spectrum Shield enables your Arduino with the capability of splitting a stereo audio input into 7-bands per channel. You can then read the amplitude of each channel using the ADC on your Arduino allowing you to control everything from LEDs to motors, pumps to relays, or even fire, all with sound. DEV-13116
zł149.36
24h
Available quantity: 1
Available
Audio recorder module that allows for multiple recording and playback of sounds. Comes with a loudspeaker
zł11.86
24h
Available quantity: 4
Available
Gravity: Voice Recorder Module is a sound recording module powered by 5V voltage. It can store sounds up to 10 seconds long. DFRobot SEN0197
zł26.24
24h
Available quantity: 1
Available
Sound recording module that can store sounds up to 40 minutes long. It allows you to download the recordings to a computer via USB type C. DFRobot DFR0745
zł33.06
24h
Available quantity: 2
Available
Audio player and recorder with built-in VS1003 codec, 3.5 mm jack audio output and a microphone
zł34.21
24h
Available quantity: 2
Available
Module for recording sounds, which can store recordings up to 20 seconds. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 107020007
zł37.82
24h
Available quantity: 2
Available
Sound recording module with I2C interface. It can store sounds up to 100 seconds long. DFRobot SEN0197