zł269.01
MOSFET Driver - module with MOSFET transistor with N channel
ID: 1183274
5906623431519
zł20.74
Tax included
zł16.86 tax excl.
AO3406 MOSFET transistor module with N channel and JST PH2.0 connector designed to control motor, solenoid or LEDs. Adafruit 5648
Description
Module with MOSFET transistor and JST PH2.0 connector designed to control motor, solenoid or LEDs. It allows you to easily connect a microcontroller with the controlled component without the need to solder the circuit to the transistor or connect components on a contact board. The module can be supplied with a voltage from 3 V to 30 V and controlled by a signal with a logic level from 3 V to 20 V. The output has a terminal connector. It uses an N-channel MOSFET AO3406 transistor, and a 1N4007 protection diode is also included on the board. In addition to the JST PH2.0 connector, the user also has a goldpin connector with a 2.54 mm raster. The module will prove useful during device prototyping.
Features
- MOSFET transistor AO3406 with N channel
- Supply voltage: 3 V to 30 V
- Control voltage: 3 V to 20 V
- Conduction current: 1.5 A (continuous), 3 A (instantaneous)
- RdsOn: 70 mΩ
- Connector: JST PH2.0, goldpin 2.54 mm
- Terminal connector for connecting outputs
- Dimensions: 25.4 x 17.7 x 7.2 mm
- Weight: 2.4 g
1183274
Data sheet
- Output current
- 1,5 A
- Number of channels
- 1
- Executive element
- MOSFET
- Coil voltage
- Nie dotyczy
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Pin header goldpin black 1x40 pins. Straight connector for through-hole assembly. 2.54mm pitch.
zł1.50
24h
Available quantity: 11082
Available
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.31
24h
Available quantity: 382
Available
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł4.31
24h
Available quantity: 80
Available
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
zł5.10
24h
Available quantity: 779
Available
Other products in the same category (16)
The module contains four 5V relays with a maximum current of 10A (250 VAC) and opto-isolated inputs, and with jumpers it is possible to select switching with high or low status. The module is equipped with screw connectors. modRL04_ISO
zł22.40
4 weeks
No product available!
The module contains eight 5V relays with a maximum current of 10A (250 VAC) and opto-isolated inputs, and with jumpers it is possible to select high or low switching. The module is equipped with screw connectors. modRL08_ISO
zł21.01
4 weeks
No product available!
Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 2895
zł52.00
24h
Available quantity: 1
Available
Adafruit FeatherWing module with snap relay. It allows you to control high-power components using a microcontroller. It allows switching current to 2A (at 40VAC or 30VDC) and voltage up to 250VAC. Adafruit 2923
zł40.74
24h
Available quantity: 1
Available
Your 5V system can wield great power with this big, beefy relay board. Kit contains all the parts you need to get your high-power load under control. Sparkfun KIT-13815
zł52.71
24h
Available quantity: 1
Available
Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 3191
zł49.73
24h
Available quantity: 1
Available
Module with MOSFET transistor, 5-36 V, 20 A, switching frequency 1 kHz. DFRobot DFR0457
zł16.56
24h
Available quantity: 7
Available
The module is equipped with eight 10A / 250VAC relays controlled independently via a serial bus (UART) or from a PC (through a microUSB connector). The NO / NC contacts of the relays have been led to the ARK screw terminals. The board recommended for use with Arduino enables the control of eight relays using only two microcontroller lines. ICSTATION ICSE014A
zł50.41
4 weeks
No product available!
The module is equipped with four 10A / 250VAC relays controlled independently via a serial bus (UART) or from a PC (through a microUSB connector). The NO / NC contacts of the relays have been led to the ARK screw terminals. ICSTATION ICSE012A
zł44.58
4 weeks
No product available!
Programmable time module with relay, allows you to set the time and manner of relay reaction on the trigger signal, has a built-in LED display. It can be supplied with voltage from the range of 6 - 30VDC or using the microUSB connector
zł9.67
4 weeks
No product available!
The module with the HLS8-T73 relay with a load up to 5 A. The board is equipped with a Grove connector and is controlled by a digital input. Seeed Studio 103020005
zł13.80
24h
Available quantity: 5
Available
The module with the TPL5110 timer, which can generate a signal with an adjustable period from 100 ms to 2 h. It also works well as an external Watchdog Timer. Adafruit 3435
zł26.11
4 weeks
No product available!
Gravity: Digital 10A Relay Module is a module with 10A 35VAC / 30VDC relay compatible with devices with control signals in the range of 2.8 ... 5.5V. DFRobot DFR0473
zł19.93
4 weeks
No product available!
The module contains a 5 V relay with a maximum current of 10 A (250 VAC) and optoisolated inputs, and with jumpers it is possible to select high or low switching. The module is equipped with screw connectors
zł8.84
24h
Available quantity: 39
Available
Module with 5 A 250 VAC relay. DFRobot DFR0017
zł12.63
24h
Available quantity: 3
Available
8-channel module with relays designed for minicomputers Raspberry Pi. It allows you to control devices powered by high voltage. Waveshare RPi Relay Board (B)
zł80.43
24h
Available quantity: 4
Available
AO3406 MOSFET transistor module with N channel and JST PH2.0 connector designed to control motor, solenoid or LEDs. Adafruit 5648