LilyPad LilyMini ProtoSnap - prototype module for interactive clothes
ID: 563586
5906623417797
zł88.20
Tax included
zł71.71 tax excl.
The LilyPad series module is designed for prototyping interactive e-textiles. It consists of a board with a SAMD11 microcontroller and a CR2032 battery socket, LEDs, a light sensor and a button. SparkFun DEV-14063
Description
The LilyPad series module is designed for prototyping interactive e-textiles. It consists of a board with a SAMD11 microcontroller and a CR2032 battery socket, LEDs, a light sensor and a button. LilyMini ProtoSnap comes with a factory programmed microcontroller that uses all the components connected to it. The program used has three modes that can be selected by pressing the LilyPad button in the lower left corner of ProtoSnap. The built-in RGB LED on the LilyMini will change color to indicate which mode has been selected:
- White - all LEDs on.
- Magenta - LEDs come and go with the rhythm of your breathing. When the light sensor is obstructed, the LEDs turn off faster.
- Cyan - LEDs off. When the light sensor is obstructed, the LEDs will flash.
The module is divided into 7 tiles, which are connected after being taken out of the box. This allows you to quickly test the prototype of the device, which, after dividing into smaller modules, can be transferred and sewn into the garment. Each tile has dedicated holes for easy installation. The instructions for use and an example of use are available in the guide.
Features
- SAMD11 microcontroller
- Light sensor
- Button
- 4 x LED
- CR2032 battery socket with battery
- Holes allowing sewing to clothes with conductive threads
Kit contains
- LilyMini (with battery)
- LilyPad Light Sensor
- LilyPad Button
- 4 x LilyPad LEDs
563586
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
DEV-10867 - Conductive Thread Bobbin - 30ft (Stainless Steel)
zł22.90
24h
Available quantity: 2
Available
Adafruit 640 - Stainless Thin Conductive Thread - 2 ply - 23 meter/76 ft
zł39.62
24h
Available quantity: 2
Available
Adafruit 603 - Stainless Thin Conductive Yarn / Thick Conductive Thread - 35 ft
zł26.53
24h
Available quantity: 3
Available
Kit with LEDs, battery, needles and conductive thread that allows you to sew LED lighting into clothes. SparkFun DEV-11590
zł103.17
24h
Available quantity: 1
Available
Other products in the same category (16)
This is the second version of the Flora NeoPixels, which runs at at \'high speed\' 800KHz communication. Adafruit 1260
zł43.46
24h
Available quantity: 1
Available
Kit with LEDs, battery, needles and conductive thread that allows you to sew LED lighting into clothes. SparkFun DEV-11590
zł103.17
24h
Available quantity: 1
Available
FLORA is Adafruit\'s fully-featured wearable electronics platform. It\'s a round, sewable, Arduino-compatible microcontroller designed to empower amazing wearables projects. Adafruit 659
Regular pricezł105.32zł91.00
24h
Available quantity: 1
Available
Microcontroller board controlled by ATmega32U4 with Arduino bootloader. Due to the dimensions and openings, it is perfect for electronic components sewn into clothes. It has a built-in JST connector with a charging circuit and a switch and is programmed via a micro USB connector. SparkFun DEV-12049
zł139.00
3 weeks
No product available!
Microcontroller board controlled by ATmega32U4 with Arduino bootloader. Due to its dimensions and holes, it will be excellent for electronic components sewn into clothing. It has a built-in JST connector with charging circuit and on/off switch and is programmable via micro USB. SparkFun DEV-14631
zł179.90
3 weeks
No product available!
A set of 20 modules with RGB diodes with a diameter of 12.5 mm. The diodes have a 24-bit range of colors. Adafruit 1559
zł206.07
4 weeks
No product available!
GEMMA M0 is an intelligent clothing controller from Adafruit. In relation to the classic GEMMA board, it was equipped with a 32-bit ATSAMD21E18 microcontroller (based on Cortex M0 +). It has GPIO pins, RGB DotStar diode. The board can be powered by a 3.7 V Li-Ion battery (JST connector). Adafruit 3501
zł58.66
4 weeks
No product available!
The Flora budget starter kit contains everything you need to start an adventure with smart clothing. Included, among others motherboard, LED diodes, conductive cord, battery basket. Adafruit 1405
zł206.07
4 weeks
No product available!
Available
TCS34725 has RGB and Clear light sensing elements. An IR blocking filter, integrated on-chip and localized to the color sensing photodiodes, minimizes the IR spectral component of the incoming light and allows color measurements to be made accurately. Adafruit 1356
zł46.89
24h
Available quantity: 2
Available
Slim 3V battery powered LEDs that are perfect for e-textile projects. With clearly marked connectors and double-sided PCB, these LEDs are easy to connect and highly durable, making them the perfect choice for interactive clothing, accessories and decorations that combine fashion with modern technology. Kitronik 2714
zł23.42
24h
Available quantity: 4
Available
Kitronik 2752 is a sewable coin cell battery holder with a built-in latching switch, designed for e-textile projects. It enables easy powering of electronic circuits in clothing and allows users to control their operation using the integrated switch.
zł13.55
24h
Available quantity: 10
Available
A miniature module with a LiPo battery charger with a capacity of 500 mA. SparkFun DEV-11893
zł51.30
24h
Available quantity: 1
Available
Available
Adafruit 1059 - Flora Wearable Ultimate GPS Module
zł205.62
24h
Available quantity: 1
Available
Button cell battery holder specially designed for e-textiles from Kitronik. It has large connection points that allow easy connection of the conductive thread. Dedicated to CR2032 batteries. Kitronik 2711
zł9.04
24h
Available quantity: 5
Available
The LilyPad series module is designed for prototyping interactive e-textiles. It consists of a board with a SAMD11 microcontroller and a CR2032 battery socket, LEDs, a light sensor and a button. SparkFun DEV-14063