zł47.69 tax excl.
GEMMA M0 is an intelligent clothing controller from Adafruit. In relation to the classic GEMMA board, it was equipped with a 32-bit ATSAMD21E18 microcontroller (based on Cortex M0 +). It has GPIO pins, RGB DotStar diode. The board can be powered by a 3.7 V Li-Ion battery (JST connector). Adafruit 3501
GEMMA M0 is a smart clothing controller from Adafruit. In relation to the classic GEMMA board, it was equipped with a 32-bit ATSAMD21E18 microcontroller (based on Cortex M0 +). Which has more FLASH memory, RAM and can work at a higher frequency (48 MHz) than the ATtiny85 microcontroller which had a classic GEMMA board. The board has GPIO pins (which can act as digital I / O, analog inputs / outputs or generate PWM signal), diode RGB DotStar.
The board is compatible with Arduino , so you can program it in the Arduino IDE, like any other Arduino board . It is also possible to program using the CircuitPython environment.
The board can be powered by a 3.7 V Li-Ion battery .
properties
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
DEV-10867 - Conductive Thread Bobbin - 30ft (Stainless Steel)
TCS34725 has RGB and Clear light sensing elements. An IR blocking filter, integrated on-chip and localized to the color sensing photodiodes, minimizes the IR spectral component of the incoming light and allows color measurements to be made accurately. Adafruit 1356
A set of 20 modules with RGB diodes with a diameter of 12.5 mm. The diodes have a 24-bit range of colors. Adafruit 1559
No product available!
The Flora starter kit contains everything you need to start an adventure with smart clothing. Included, among others main board, GPS module, LED diodes, conductive cord, battery basket. Adafruit 1090
No product available!
A set of 20 modules with RGB diodes with a diameter of 12.5 mm. The diodes have a 24-bit range of colors. Adafruit 1559
No product available!
This module allows you to automatically turn on LEDs in the dark thanks to a built-in light sensor. It comes with a CR2032 battery holder and a slide switch to turn the module on and off. It also has two sets of pads for connecting LEDs, allowing for flexible lighting design. Kitronik 2721
Power module designed to work with LilyPad boards. It is equipped with a switch and a CR2032 battery socket. SparkFun DEV-13883
A switch for e-textile projects that allows you to easily turn circuits on and off with a single click. Thanks to its latching mechanism, it works like a typical switch – one press turns on the power, and another cuts it off. Equipped with large "IN" and "OUT" contact pads, it allows for convenient sewing of conductive thread and quick connection of components such as LEDs or buzzers. Kitronik 2753
No product available!
FLORA is Adafruit\'s fully-featured wearable electronics platform. It\'s a round, sewable, Arduino-compatible microcontroller designed to empower amazing wearables projects. Adafruit 659
A miniature module with a programmed AVR Attiny85 microcontroller, equipped with 8 KB of Flash memory, 4 digital pins, analog input and 2 PWM channels. By connecting the LEDs to the digital outputs of the module, interesting lighting effects can be obtained. SparkFun DEV-10899
Kit with LEDs, battery, needles and conductive thread that allows you to sew LED lighting into clothes. SparkFun DEV-11590
The LilyPad series module is designed for prototyping interactive e-textiles. It consists of a board with a SAMD11 microcontroller and a CR2032 battery socket, LEDs, a light sensor and a button. SparkFun DEV-14063
Microcontroller board controlled by ATmega32U4 with Arduino bootloader. Due to its dimensions and holes, it will be excellent for electronic components sewn into clothing. It has a built-in JST connector with charging circuit and on/off switch and is programmable via micro USB. SparkFun DEV-14631
No product available!
Slim 3V battery powered LEDs that are perfect for e-textile projects. With clearly marked connectors and double-sided PCB, these LEDs are easy to connect and highly durable, making them the perfect choice for interactive clothing, accessories and decorations that combine fashion with modern technology. Kitronik 2714
A miniature module with a LiPo battery charger with a capacity of 500 mA. SparkFun DEV-11893
No product available!
XBee adapter with pads with holes for sewing the module to clothes and fabrics. SparkFun DEV-12921
Adafruit 1059 - Flora Wearable Ultimate GPS Module
This e-textile module allows you to program interactive projects such as clothing, accessories, and educational gadgets. It features a PICAXE 14M2 chip, a white LED, a momentary pushbutton, and 6 I/O pins with PWM and ADC functionality, allowing you to control LEDs, buzzers, and other components. The module is powered from 3 to 5.5V via a JST connector or wired connections, and its large connection points facilitate installation in fabrics. Kitronik 2751
GEMMA M0 is an intelligent clothing controller from Adafruit. In relation to the classic GEMMA board, it was equipped with a 32-bit ATSAMD21E18 microcontroller (based on Cortex M0 +). It has GPIO pins, RGB DotStar diode. The board can be powered by a 3.7 V Li-Ion battery (JST connector). Adafruit 3501