Lilypad USB Plus - mini module with ATmega32U4 microcontroller

A motion-activated module that activates the circuit when tilted 10° from the horizontal position. Equipped with double-sided connection points for conductive thread, it can be easily incorporated into clothing, bags, or interactive decorations. The module supports voltages up to 24 V and a maximum current of 25 mA, and its compact size makes it convenient for small e-textile projects. Kitronik 2710

This module allows you to automatically turn on LEDs in the dark thanks to a built-in light sensor. It comes with a CR2032 battery holder and a slide switch to turn the module on and off. It also has two sets of pads for connecting LEDs, allowing for flexible lighting design. Kitronik 2721

Kitronik 2752 is a sewable coin cell battery holder with a built-in latching switch, designed for e-textile projects. It enables easy powering of electronic circuits in clothing and allows users to control their operation using the integrated switch.

GEMMA M0 is an intelligent clothing controller from Adafruit. In relation to the classic GEMMA board, it was equipped with a 32-bit ATSAMD21E18 microcontroller (based on Cortex M0 +). It has GPIO pins, RGB DotStar diode. The board can be powered by a 3.7 V Li-Ion battery (JST connector). Adafruit 3501

A compact light sensor for e-textile projects that allows devices to be activated based on ambient light levels. The OUT output generates a voltage ranging from 0.9V in low light to 2.9V in bright environments, allowing for the creation of interactive effects in clothing and accessories. Large connection points allow for easy sewing of conductive thread, and the small size makes the module easy to integrate into a variety of projects. Kitronik 2754

DEV-23903

Button cell battery holder specially designed for e-textiles from Kitronik. It has large connection points that allow easy connection of the conductive thread. Dedicated to CR2032 batteries. Kitronik 2711

The Flora budget starter kit contains everything you need to start an adventure with smart clothing. Included, among others motherboard, LED diodes, conductive cord, battery basket. Adafruit 1405

This e-textile module allows you to program interactive projects such as clothing, accessories, and educational gadgets. It features a PICAXE 14M2 chip, a white LED, a momentary pushbutton, and 6 I/O pins with PWM and ADC functionality, allowing you to control LEDs, buzzers, and other components. The module is powered from 3 to 5.5V via a JST connector or wired connections, and its large connection points facilitate installation in fabrics. Kitronik 2751

The Flora starter kit contains everything you need to start an adventure with smart clothing. Included, among others main board, GPS module, LED diodes, conductive cord, battery basket. Adafruit 1090

Kit with LEDs, battery, needles and conductive thread that allows you to sew LED lighting into clothes. SparkFun DEV-11590

The LilyPad series module is designed for prototyping interactive e-textiles. It consists of a board with a SAMD11 microcontroller and a CR2032 battery socket, LEDs, a light sensor and a button. SparkFun DEV-14063

Microcontroller board controlled by ATmega32U4 with Arduino bootloader. Due to the dimensions and openings, it is perfect for electronic components sewn into clothes. It has a built-in JST connector with a charging circuit and a switch and is programmed via a micro USB connector. SparkFun DEV-12049

Sewable with a 3-pin JST wiring adapter with 3 holes on the board perfect for conductive thread or soldering, wired to a single 3-pin JST-PH Adapter. Sdafruit 2566

A miniature module with a LiPo battery charger with a capacity of 500 mA. SparkFun DEV-11893

This is the second version of the Flora NeoPixels, which runs at at \'high speed\' 800KHz communication. Adafruit 1260