LilyPad Simple Power - mini LiPo battery charger module

TCS34725 has RGB and Clear light sensing elements. An IR blocking filter, integrated on-chip and localized to the color sensing photodiodes, minimizes the IR spectral component of the incoming light and allows color measurements to be made accurately. Adafruit 1356

A compact light sensor for e-textile projects that allows devices to be activated based on ambient light levels. The OUT output generates a voltage ranging from 0.9V in low light to 2.9V in bright environments, allowing for the creation of interactive effects in clothing and accessories. Large connection points allow for easy sewing of conductive thread, and the small size makes the module easy to integrate into a variety of projects. Kitronik 2754

DEV-13342

A motion-activated module that activates the circuit when tilted 10° from the horizontal position. Equipped with double-sided connection points for conductive thread, it can be easily incorporated into clothing, bags, or interactive decorations. The module supports voltages up to 24 V and a maximum current of 25 mA, and its compact size makes it convenient for small e-textile projects. Kitronik 2710

This module allows you to automatically turn on LEDs in the dark thanks to a built-in light sensor. It comes with a CR2032 battery holder and a slide switch to turn the module on and off. It also has two sets of pads for connecting LEDs, allowing for flexible lighting design. Kitronik 2721

The Flora budget starter kit contains everything you need to start an adventure with smart clothing. Included, among others motherboard, LED diodes, conductive cord, battery basket. Adafruit 1405

GEMMA M0 is an intelligent clothing controller from Adafruit. In relation to the classic GEMMA board, it was equipped with a 32-bit ATSAMD21E18 microcontroller (based on Cortex M0 +). It has GPIO pins, RGB DotStar diode. The board can be powered by a 3.7 V Li-Ion battery (JST connector). Adafruit 3501

Sewable with a 3-pin JST wiring adapter with 3 holes on the board perfect for conductive thread or soldering, wired to a single 3-pin JST-PH Adapter. Sdafruit 2566

Kitronik 2718 is a miniature sewable coin cell battery holder designed for e-textile projects, enabling easy power supply to electronic circuits in clothing. Thanks to its compact size and specially designed mounting holes, the holder can be easily sewn onto fabric, making it ideal for use in smart clothing and wearable accessories.

Kitronik 2752 is a sewable coin cell battery holder with a built-in latching switch, designed for e-textile projects. It enables easy powering of electronic circuits in clothing and allows users to control their operation using the integrated switch.

Kit with LEDs, battery, needles and conductive thread that allows you to sew LED lighting into clothes. SparkFun DEV-11590

Microcontroller board controlled by ATmega32U4 with Arduino bootloader. Due to the dimensions and openings, it is perfect for electronic components sewn into clothes. It has a built-in JST connector with a charging circuit and a switch and is programmed via a micro USB connector. SparkFun DEV-12049

FLORA is Adafruit\'s fully-featured wearable electronics platform. It\'s a round, sewable, Arduino-compatible microcontroller designed to empower amazing wearables projects. Adafruit 659

Adafruit 1222

A miniature module with a programmed AVR Attiny85 microcontroller, equipped with 8 KB of Flash memory, 4 digital pins, analog input and 2 PWM channels. By connecting the LEDs to the digital outputs of the module, interesting lighting effects can be obtained. SparkFun DEV-10899

A switch for e-textile projects that allows you to easily turn circuits on and off with a single click. Thanks to its latching mechanism, it works like a typical switch – one press turns on the power, and another cuts it off. Equipped with large "IN" and "OUT" contact pads, it allows for convenient sewing of conductive thread and quick connection of components such as LEDs or buzzers. Kitronik 2753