![LilyTwinkle ProtoSnap - a set for highlighting clothes LilyTwinkle ProtoSnap - a set for highlighting clothes](https://kamami.pl/41471-large_default/lilytwinkle-protosnap-a-set-for-highlighting-clothes-dev-11590.jpg)
![LilyTwinkle ProtoSnap - a set for highlighting clothes LilyTwinkle ProtoSnap - a set for highlighting clothes](https://kamami.pl/41471-large_default/lilytwinkle-protosnap-a-set-for-highlighting-clothes-dev-11590.jpg)
zł83.88 tax excl.
Kit with LEDs, battery, needles and conductive thread that allows you to sew LED lighting into clothes. SparkFun DEV-11590
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
Kit with LEDs, battery, needles and conductive thread that allows you to sew LED lighting into clothes. It also enables prototyping of devices without the use of a breadboard. The instructions for use and an example of use are available in the guide.
DEV-10867 - Conductive Thread Bobbin - 30ft (Stainless Steel)
The Flora budget starter kit contains everything you need to start an adventure with smart clothing. Included, among others motherboard, LED diodes, conductive cord, battery basket. Adafruit 1405
No product available!
GEMMA M0 is an intelligent clothing controller from Adafruit. In relation to the classic GEMMA board, it was equipped with a 32-bit ATSAMD21E18 microcontroller (based on Cortex M0 +). It has GPIO pins, RGB DotStar diode. The board can be powered by a 3.7 V Li-Ion battery (JST connector). Adafruit 3501
No product available!
Microcontroller board controlled by ATmega32U4 with Arduino bootloader. Due to its dimensions and holes, it will be excellent for electronic components sewn into clothing. It has a built-in JST connector with charging circuit and on/off switch and is programmable via micro USB. SparkFun DEV-14631
No product available!
This is the second version of the Flora NeoPixels, which runs at at \'high speed\' 800KHz communication. Adafruit 1260
A miniature module with a LiPo battery charger with a capacity of 500 mA. SparkFun DEV-11893
The Flora starter kit contains everything you need to start an adventure with smart clothing. Included, among others main board, GPS module, LED diodes, conductive cord, battery basket. Adafruit 1090
No product available!
A set of 20 modules with RGB diodes with a diameter of 12.5 mm. The diodes have a 24-bit range of colors. Adafruit 1559
No product available!
Sewable with a 3-pin JST wiring adapter with 3 holes on the board perfect for conductive thread or soldering, wired to a single 3-pin JST-PH Adapter. Sdafruit 2566
No product available!
Power module designed to work with LilyPad boards. It is equipped with a switch and a CR2032 battery socket. SparkFun DEV-13883
A miniature module with a programmed AVR Attiny85 microcontroller, equipped with 8 KB of Flash memory, 4 digital pins, analog input and 2 PWM channels. By connecting the LEDs to the digital outputs of the module, interesting lighting effects can be obtained. SparkFun DEV-10899
No product available!
The LilyPad series module is designed for prototyping interactive e-textiles. It consists of a board with a SAMD11 microcontroller and a CR2032 battery socket, LEDs, a light sensor and a button. SparkFun DEV-14063
XBee adapter with pads with holes for sewing the module to clothes and fabrics. SparkFun DEV-12921
Kit with LEDs, battery, needles and conductive thread that allows you to sew LED lighting into clothes. SparkFun DEV-11590