![Gravity: Nano I / O Shield - expansion board for Arduino Nano Gravity: Nano I / O Shield - expansion board for Arduino Nano](https://kamami.pl/29771-large_default/gravity-nano-i-o-shield-expansion-board-for-arduino-nano.jpg)
![Gravity: Nano I / O Shield - expansion board for Arduino Nano Gravity: Nano I / O Shield - expansion board for Arduino Nano](https://kamami.pl/29771-large_default/gravity-nano-i-o-shield-expansion-board-for-arduino-nano.jpg)
zł31.65 tax excl.
Nano I / O Shield for Arduino Nano is an expansion board for Arduino Nano that provides digital, analog pins, power inputs and a connector for the Bluetooth module. DFRobot DFR0012
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
Gravity: Nano I / O Shield for Arduino Nano is a small expansion board designed for Arduino Nano. It provides 16 digital pins and 8 pins with VCC and GND pins (compatible with Gravity connectors). They allow you to easily connect Gravity modules to the expansion board. Additional servo power supply allows direct connection to the board. Shield also has a connector for the Bluetooth module.
Small evaluation board based on the ATmega328, RoHS
Extension board for Arduino Nano and Uno, 14 GPIO lines, connectors with I2C and UART interface lines. The board also has a RESET button and a voltage stabilizer
Gravity: IO Expansion & Motor Driver Shield is an Arduino compatible expansion board that provides digital I / O ports, analog I2C, SPI and UART interfaces, as well as a DC motor driver. DFRobot DFR0502
Shield for Arduino containing the most commonly used peripherals in an easy-to-use form. It is equipped with: OLED display, RGB diode, buttons, temperature and humidity sensor and joystick. DFRobot DFR0270
Adafruit 1141 - Adafruit Assembled Data Logging shield for Arduino
Gravity: Heart Rate Monitor Sensor is a sensor used to measure heart activity. Adapted for easy use with Arduino. SparkFun SEN0213
Shield with a 6-pin JST SH connector dedicated to Arduino Mini. It allows you to connect the GPS module with the GP-735 chip. SparkFun GPS-14030
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
(DFR0144) Relay Shield for Arduino V2.1
Shield - Xbee w / o RF module
Controller module dedicated to Arduino boards. Equipped with 4 buttons, a two-axis joystick and an Xbee connector. DFRobot DFR0008
RGB Panel Shield is an extension in the form of shield overlays designed for Arduino. With its help it is possible to control the RGB 32x32 LED display (refresh 1: 8). Communication with the display takes place via a 2x8 connector. SparkFun SPX-14721
Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000
The overlay allows for easier connection of wires to the Arduino UNO R3 board. Thanks to the screw connections, it is possible to fast and securely fix the cable, and the built-in female connectors allow the application of additional Arduino shields. Screw shield
The shield allows for easier connection of cables to the Arduino UNO R3 board. Thanks to the screw connectors, it is possible to fast and secure the cable, goldpin connectors allow you to easily connect the servo, and the built-in female connectors allow you to put additional Arduino shields
The X-NUCLEO-53L0A1 expansion board features the VL53L0X ranging and gesture detection sensor, based on ST’s FlightSense™, Time-of-Flight technology. It is an evaluation board that provides an introduction to the ranging and gesture detection capabilities of the VL53L0X module
Shield dedicated to Arduino boards, which allows you to program AVR systems. Equipped with ISP connectors (6-pin and 10-pin) and a ZIF-28 base. AVR ISP Shield
Nano I / O Shield for Arduino Nano is an expansion board for Arduino Nano that provides digital, analog pins, power inputs and a connector for the Bluetooth module. DFRobot DFR0012