

Uninterruptible power supply module designed for Raspberry Pi Pico. The power supply, after connecting the Li-Po battery, maintains a stable output voltage of 5 V even after the loss of power, which allows the device to continue operating and safely shut down. The battery charge status is indicated by built-in LEDs, and full battery status monitoring is possible thanks to the I2C interface. The board has a battery charging circuit and protection against overcharging and discharging, overcurrent, short-circuit and reverse polarity protection. It is connected to the Raspberry Pi Pico via a dedicated connector. The manufacturer has prepared numerous examples in C/C++ and MicroPython for the set. Full documentation is available on the product Wiki page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Module with the RP2040 microcontroller with two ARM Cortex-M0 + cores operating at 133 MHz, 256 kB RAM and 30 GPIO. The board also has 2 MB of external QSPI flash memory. Module can be programmed in C/C++ or microPython. Raspberry Pi Pico
Module with LCD IPS display, 1.14" diagonal and 240x135 px resolution. Communication via SPI interface. Waveshare Pico-LCD-1.14
A pin expander for Raspberry Pi Pico boards. It is equipped with a standard female connector and four sets of male strips 2x20 pins. Waveshare Pico-Quad-Expander
A pin expander for Raspberry Pi Pico boards. It is equipped with a standard female connector and two sets of male strips 2x20 pins. Waveshare Pico-Dual-Expander
Module with the RP2040 microcontroller with two ARM Cortex-M0 + cores operating at 133 MHz, 256 kB RAM and 30 GPIO. The board also has 2 MB of external QSPI flash memory. Module can be programmed in C/C++ or microPython. Version with soldered connectors. Raspberry Pi SC0917
Module with a 2-channel driver for DC motors L293D designed to work with the Raspberry Pi Pico. It can work with a voltage from 6 to 12 V and a current of up to 600 mA. SB Components 21468
Shield with two relays for Raspberry Pi Pico, provides control of devices up to 250 VAC/3 A or 30 VDC/3 A, equipped with LEDs indicating the status of the relays and opto-isolation, ideal for home automation and other DIY projects
QVGA monochrome camera module with HM01B0 sensor working with Raspberry Pi Pico. It uses 1 bit video interface and I2C to configure the registers. ArduCAM B0315
Expansion module designed for Raspberry Pi Pico boards. Allows you to add CAN bus based communication to your project. Waveshare Pico-CAN-B
Kit for controlling soil moisture of cultivated plants. Equipped with a Raspberry Pi Pico W-based controller and soil moisture sensors with wires. Pimoroni PIM627
No product available!
Audio module with DAC and headphone amplifier designed to work with the Raspberry Pi Pico. It is based on the PCM5100A system and communicates via the I2S interface. Pimoroni PIM544
No product available!
A compact board that allows you to control up to 8 servos simultaneously, making it ideal for advanced robotic projects. Equipped with standard 3-pin connectors, it allows you to easily connect servos without soldering, and additional GPIO pins and a 3V power supply from Pico allow you to expand your projects with new devices. The board\'s power supply is stabilized, and additional features such as an on/off switch and reverse polarity protection increase its safety and convenience of use. Kitronik 5339
A module with a barcode and QR scanner designed to work with the Raspberry Pi Pico. It allows you to read one-dimensional and two-dimensional codes using the intelligent image recognition algorithm. SB Components 22441
Module with environmental sensors designed for Raspberry Pi Pico. It allows you to measure temperature, humidity, pressure, illuminance, detection of VOC, IR and UV radiation and orientation. Waveshare Pico-Environment-Sensor
A set of goldpin male connectors intended for Raspberry Pi Pico boards. The set includes two 20-pin strips and one 3-pin strip with a pitch of 2.54 mm. Soldered connectors enable easy connection of expansion modules and other accessories
Uninterruptible power supply module for Raspberry Pi Pico, which allows you to continue work and safely shut down the microcomputer after a power failure. Waveshare Pico-UPS-A-EN
4-channel module with relays designed to work with the Raspberry Pi Pico. It can switch signals up to 250 V AC and 7 A or 30 V DC and 10 A. SB Components 21178
No product available!
Module with 4-digit 8-segment LED display. Communication via the SPI interface. Waveshare Pico-8SEG-LED
Prototype board designed to work with the Raspberry Pi Pico. It is equipped with 120 holes with a 2.54 mm pitch and allows you to build your own circuits and connections, while maintaining compact dimensions. Pimoroni PIM554
Universal module dedicated to e-Paper displays. It is equipped with connectors compatible with the Raspberry Pi Pico. It allows you to connect a display through one of the two FPC sockets. SB Components 26241
Module with environmental sensors for Raspberry Pi Pico. It allows you to measure temperature, humidity, air quality pressure and color detection. SB Components 22366
Uninterruptible power supply module for Raspberry Pi Pico, allowing you to continue working and safely shut down after a power failure. Waveshare Pico-UPS-B