Pmod-DA2 - Two 12-bit D/A outputs
The Digilent Pmod DA2 Digital to Analog peripheral module converts signals from digital values to analog voltages on two channels simultaneously with 12-bit resolution. The Pmod DA2 uses a 6-pin header connector and at less then one square inch, is small enough to be located where the reconstructed signal is required.
Key Features:

Download:
Code: 210-113
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Digital logic level shifter ideal for users who want to supply logic signals following a 3.3V CMOS standard but have an alternate logic level output that is used for other applications, such as JTAG programming. 410-320
No product available!
Graphical display, users may show off graphs, full-color pictures, text, and anything else they want to see by communicating with it through SPI. Digilent 410-323
The Digilent Pmod COLOR is a color sensor module with the ability to sense red, green, blue and clear light. Digilent 410-348
No product available!
The Pmod BLE module is a Bluetooth module with powerful capabilities. Thanks to communication via the UART port, the module can be connected to any platform equipped with this interface. The module is equipped with the Roving Networks RN4870 system, in which a full Bluetooth interface is built-in. Digilent 410-359
KAmodMPL3115A2 is a module with an atmospheric pressure sensor MPL3115A2 from NXP. Sensor allows to make a measurement in the range of 200...1100hPa (20...110kPa). Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMPL3115A2
KAmodMAG3110FC is a module with magnetic field sensor MAG3110FC from NXP. The sensor measures the magnetic field in the range of ±1000μT, with a resolution of 0.1μT. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMAG3110FC
KAmodMMA8653FC is a module with NXP's MMA8653FC three-axis accelerometer. The sensor allows the measurement of acceleration in the range of ± 2g / ± 4g / ± 8g, the measurement frequency is from 1.56 Hz to 800 Hz. Communication with the sensor takes place via the I2C interface
Module with DS18B20 temperature sensor from Dallas Semiconductor. The sensor used allows you to measure temperatures in the range -55 ~ 125 ° C with an accuracy of ± 0.5 ° C (in the range of -10 ~ 85 ° C). The 1-Wire interface is used for communication. The plate is equipped with a goldpin connector and a KAMAMI connector, allowing easy connection of the module to the commissioning kits.
No product available!
The Pmod SF3 provides users with 32 MB of non-volatile memory through the use of Micron\'s NOR Flash memory (N25Q256A). By using the SPI protocol, users can both write to and read from the flash memory. Digilent 410-340
No product available!
No product available!
Pmod PIR is a module with a PIR motion sensor (EKMC1601111), which allows you to detect motion up to 5 meters from the module. The sensor during operation is characterized by low power consumption. Digilent 410-389
Provides a 300 tie breadboard and 50 tie bus bar on an expansion card compatible with the NI myRIO Expansion Port (MXP). 210-283
No product available!
No product available!
Evaluation Board with AD7693, 1xADC, 16-bit, Sampling Rate (Per Second) 500k, Analog Devices, RoHS
No product available!
Pmod-DA2 - Two 12-bit D/A outputs