STEMMA QT DPS310 Precision Barometric Pressure/Altitude Sensor - module with a pressure sensor

The MPX5700AP air pressure sensor with a measuring range from 15 to 700 kPa. It communicates via the I2C interface. DFRobot SEN0456

The GY-BMP280 is an atmospheric pressure sensor module. It allows measurement in the range of 300 ... 1100 hPa with an accuracy of 1 hPa. The sensor uses I2C or SPI bus

Crowtail – BME280 Atmospheric Sensor 2.0 is a multifunctional environmental sensor measuring temperature, humidity, and pressure, with an I2C interface and low power consumption. It is used in weather applications, home automation, and mobile systems.

Module with pressure, temperature and humidity sensor BME280. It allows to read the atmospheric pressure in the range from 300 to 1100 hPa and communicates via the I2C interface. Pimoroni PIM472

KAmodLPS25HB is a module that allows the measurement of atmospheric pressure in the range of 260-1260hPa with a resolution of 0.01hPa, and thanks to the embedded regulator and voltage translator levels, it can be successfully used in systems supplied with a voltage of 2.5 - 5.5 V.

KAmod BMP390 contains a precise BMP390 sensor manufactured by Bosch Sensortec, enabling the measurement of atmospheric pressure and temperature. All key signals of the miniature BMP390 sensor are routed on the module board, facilitating its use in modular applications. Communication is carried out via SPI or I2C interfaces equipped with voltage level translation circuits.

A precise pressure and temperature sensor that supports I2C communication, which makes it easy to integrate with microcontrollers such as Arduino. With its compact design and versatile use in navigation, altitude measurement or GPS assistance, it is ideal for IoT projects and navigation systems. DFRobot SEN0372

Compact module with three I2C sensors, enabling measurement of temperature, humidity, pressure, light, proximity and motion. It offers two Qw/ST connectors, so you can quickly connect it to Raspberry Pi, Pico or other microcontrollers. Ideal for IoT applications, home automation and environmental analysis in mobile or stationary projects. Pimoroni PIM745

Atmospheric pressure sensor, capable of measuring up to 4060 hPa, which allows it to be used even in underwater projects to a depth of about 40 meters. Thanks to high precision (±0.5 hPa) and a sampling rate of up to 200 Hz, it is also ideal for dynamic measurements of altitude and pressure in atmospheric conditions. The built-in metal port allows remote pressure measurement through a tube, and compatibility with the STEMMA QT system and ready-made libraries for Arduino and CircuitPython make integration with microcontrollers quick and easy. Adafruit 6067

Module with the MS5611 sensor, allowing measurement of atmospheric pressure. The module has a built-in 3.3 V voltage stabilizer. It comes with a connector for self-assembly. modGY-63

KAmodLPS331 is a module that allows the measurement of atmospheric pressure in the range of 260 - 1260 hPa with a resolution of 0.02 hPa. Supply voltage 2.5 - 5.5 V,

Crowtail – BMP180 Barometer is a digital pressure and temperature sensor with an I2C interface, intended for precise measurements in mobile and environmental systems. It offers high accuracy, low power consumption, and readiness to operate without additional calibration.

The MS5803-14BA waterproof pressure sensor module. It allows measurement from 0 to 14 bar and communicates via SPI or I2C interface. SparkFun SEN-12909

This precision barometric pressure and temperature sensor is ideal for environmental applications. Its low noise floor allows for detection of elevation changes down to approximately 1 cm and offers a relative accuracy of ±0.4 Pa. It supports I2C and SPI interfaces for easy integration with microcontrollers. The pre-assembled module includes a built-in 3.3V regulator, logic level conversion, and STEMMA QT connectors. Adafruit 6407

Module with digital barometer BMP384. It enables pressure measurement in the range from 300 to 1250 hPa with 24-bit resolution and communicates via I2C. SparkFun SEN-19833

Module with pressure and temperature sensor BMP280. It allows you to read the atmospheric pressure in the range from 300 to 1100 hPa and communicates via the I2C or SPI interface. Adafruit 2651