Module with 4-element segment display. Each of the four displays consists of 14 segments, so it can display not only numbers, such as the standard 7-segment display, but also letters and special characters. The display was connected to the VK16K33 controller operating with a voltage from 4.5 V to 5 V, so that when used with Arduino, a voltage level converter is not required. The user can configure the I2C address with two jumpers, which allows you to connect up to 4 such displays on one line. The module communicates via the I2C interface and is supplied with the voltage of 3.3 V. Full documentation with examples of use is available on the product page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Module with WiFi and Bluetooth Espressif ESP32 WROOM. It integrates a set of peripheral devices - capacitive touch sensors, Hall sensors, SD card interface, Ethernet, fast SPI, UART, I2S and I2C. SparkFun WRL-15663
Board with the ATmega328 microcontroller from the AVR family, there are 20 I/O lines, 6 PWM channels, 6 analog inputs at the user\'s disposal. SparkFun DEV-15123
Flexible Qwiic cable 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single male goldpin connectors. SparkFun PRT-17912
Flexible Qwiic cable, 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single female goldpin connectors. SparkFun PRT-17261
Flexible 4-core cable, 100 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17259
Module with 2-channel DC motor driver. It allows you to control the drive with a supply voltage from 3 to 11 V and a current of 1.2 A (1.5 A instantaneous). I2C communication. SparkFun ROB-15451
No product available!
Module with a voltage level converter 3.3 V - 5 V intended for use in the Qwiic system. It has a built-in Step Up converter providing power supply with a voltage of 5 V and a current of up to 100 mA. SparkFun SPX-17238
Module with a deflection sensor with two measuring probes. The board houses the ADS1015 converter, which is an ADC converter with an output in the form of an I2C interface. SparkFun SEN-14666
No product available!
Air velocity sensor module based on the FS3000-1015 system. The board is equipped with connectors in the Qwiic standard. SparkFun SEN-18768
No product available!
The expansion module is designed to work with Raspberry Pi 400 - a portable computer built into the keyboard. The board has a 40-pin connector in the pin position and two Qwiic connectors. SparkFun DEV-17512
End module of the communication system based on QwiicBus. It allows you to extend the range of the I2C bus. SparkFun COM-16988
Module with an IO pin expander based on the TCA9534 system. It allows you to add 8 GPIO pins to an I2C-controlled project. SparkFun DEV-17047
Module with 16x2 characters LCD display and ATMega328p microcontroller. The user can communicate with the module through one of the serial interfaces: UART, I2C or SPI. SparkFun LCD-16397
No product available!
Heart rate monitor module based on the popular MAX30101 and MAX32664. The board is equipped with connectors compliant with the Qwiic standard. SparkFun SEN-15219
No product available!
Module with a capacitive touch sensor based on the CAP1203 chip. There are three touch panels on the board that can be used as separate sensors (pins CS1, CS2, CS3) or as a touch slider. I2C communication. SparkFun SEN-15344
Air quality sensor module based on SGP30 system. The board has been equipped with Qwiic connectors. SparkFun SEN-16531
Module with 16x2 characters LCD display and ATMega328p microcontroller. The user can communicate with the module through one of the serial interfaces: UART, I2C or SPI. SparkFun LCD-16396
GPS module with NEO-M9N 92-channel GNSS receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART, I2C and SPI interfaces. SparkFun GPS-15712
Miniature pressure measurement module equipped with a 25 psi piezoresistive pressure sensor. It allows you to perform calibrated and compensated pressure measurements from 60 mbar to 2.5 bar. SparkFun SEN-16476
GPS module with NEO-M9N 92-channel GNSS receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART, I2C and SPI interfaces. SparkFun GPS-17285
No product available!
Mini module with ToF VL53L5CX sensor with a matrix of 64 pixels and a range of up to 4 m. It is equipped with a Qwiic connector and communicates via the I2C interface. SparkFun SEN-19013
Module with a 4-element 14-segment display. The board is equipped with a Qwiic connector and communicates via the I2C interface. SparkFun COM-16919