- Out-of-Stock
AVT1023 A
ID: 190304
TAMPER PREAMPLIFIER WITH RIAA CHARACTERISTICS - PRINTED PLATE
TAMPER PREAMPLIFIER WITH RIAA CHARACTERISTICS - PRINTED PLATE
Producer: AVT
Despite the rapid development of digital audio technology, 'black' gramophone records enjoy unflagging popularity among audiophiles. To listen to them you need a turntable with a MM insert (with a movable magnet) equipped with an amplifier with RIAA characteristics. The kit uses a modern, double operational amplifier type TDA2320. Its characteristic feature is the low-noise input stage, full frequency compensation, high gain and close to 100 dB channel separation. Elements in the negative feedback loop shape the characteristics of the amplifier according to the RIAA standard.
The device is especially recommended to all audiophiles using analog turntables as a signal source
Selected parameters:
- two-channel, stereo system
- gain k = 38 dB (f = 1kHz)
- input voltage (maximum) 55 mV
- signal / noise ratio> 78 dB
- nonlinear distortions <0.08% (in the whole band)
- power supply - 15 V
- printed circuit board and documentation included
A version with a set of components for self-assembly is available
- A detailed description in
Download
190304
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
A pin expander designed for Raspberry Pi boards. It is equipped with a standard 40-pin connector for connecting a minicomputer and two sets of 2x20-pin outputs for connecting expansion modules. Pimoroni PIM511
Retired
No product available!
Extension module for Raspberry Pi. The board has 7 RGB LEDs, four 14-segment displays, three single-color LEDs, as well as three touch buttons, a BMP280 sensor and a buzzer. Pimoroni PIM242
Retired
No product available!
Module with 6 5x7 LED matrix displays designed to work with the Raspberry Pi. It uses IS31FL3730 drivers and communicates via the I2C interface. Pimoroni PIM187
Retired
No product available!
Module with 6 5x7 LED matrix displays designed to work with the Raspberry Pi. It uses IS31FL3730 drivers and communicates via the I2C interface. Pimoroni PIM187
Retired
No product available!
A module with 5 buttons and an RGB diode, designed to work with the Raspberry Pi. The buttons are connected to the minicomputer through the GPIO expander controlled by the I2C interface. Pimoroni PIM301
Retired
No product available!
Kit for controlling soil moisture of cultivated plants. It contains the HAT Mini module, soil moisture sensors and pots and seeds of herbs: basil, coriander and rosemary. Pimoroni PIM518
Retired
No product available!
Kit for controlling soil moisture of cultivated plants. It contains the HAT Mini module, soil moisture sensors and pots and seeds of chilli. Pimoroni PIM519
Retired
No product available!
A module with a spectrum sensor that operates in the visible light range (450-650 nm). It allows you to measure and characterize a light source or check how the tested surface absorbs or reflects light at specific wavelengths. Pimoroni PIM412
Retired
No product available!
Module with a UV ultraviolet light sensor VEML6075. It enables measurement of the level of UVA (350-375 nm) and UVB (315-340 nm) radiation. It communicates via the I2C bus. Pimoroni PIM460
Retired
No product available!
Module with 6-axis IMU motion sensor that combines a 3-axis accelerometer and a 3-axis magnetometer in one system. It communicates via the I2C bus. Pimoroni PIM376
Retired
No product available!
Module with two 5x7 LED matrix displays designed to work with the Raspberry Pi. It uses IS31FL3730 drivers and communicates via the I2C interface. Pimoroni PIM527
Retired
No product available!
Module with two 5x7 LED matrix displays designed to work with the Raspberry Pi. It uses IS31FL3730 drivers and communicates via the I2C interface. Pimoroni PIM526
Retired
No product available!
The system of a practical clock with an extremely simple design is equipped with a readable LED display, an alarm clock with a snooze function, and battery backup of the clock operation after a power failure
Retired
No product available!
Kit with DA7280 vibration motor driver module and LRA (Linear Resonant Actuator) motor. It allows you to add vibration feedback from the device to the project. SparkFun ROB-18247
Retired
No product available!
Kit with Jetson Mate base board designed for SoM modules NVIDIA Jetson Nano and Jetson Xavier NX. It allows you to connect 4 SoM modules and create a home GPU computing cluster or server. Seeed Studio 110991411
Retired
No product available!
Jetson Mate motherboard for NVIDIA Jetson Nano and Jetson Xavier NX. It allows you to connect 4 SoM modules and create a home GPU computing cluster or server. Seeed Studio 114992562
Retired
No product available!
TAMPER PREAMPLIFIER WITH RIAA CHARACTERISTICS - PRINTED PLATE