.png)
- Out-of-Stock
AVT987 B
ID: 193113
DIGITAL SOLDERING STATION RL1 - SELF-ASSEMBLY KIT
DIGITAL SOLDERING STATION RL1 - SELF-ASSEMBLY KIT
Producer: AVT
Analogue soldering stations for temperature control use on / off binary systems. In this type of solutions, the temperature can oscillate around the set value even by several dozen degrees. If we want precise temperature stabilization, use the continuous control algorithm to control the heater. It is characterized by smoothly adjustable heater power - depending on the temperature.
The presented putty uses the PID (proportional-integral-derivative) algorithm. The clear LCD display presents all settings and allows you to control the operation of the device. The thermocouple type K was used as the temperature sensor. The soldering station is controlled by the ATmega8 microprocessor, to which the software was written using the GCC compiler.
The device is especially recommended in amateur electronics workshops and on the website
Selected parameters:
- PID regulation ensuring high temperature stability
- cooperation with any soldering iron supplied with 24V voltage and having a built-in K-type thermocouple
- accuracy of 1stC temperature measurement
- temperature control range 80-450 ° C
- the SLEEP function reduces the wear of the mainsail
- auto-tuning the regulator adjusting the PID settings to the soldering iron
- readout of settings - 2x16 alphanumeric LCD display
- power supply - 230Vac
- tile dimensions:
- driver board: 98x75mm
- power supply board: 40x54mm
- in the set a printed circuit board, programmed layout, set of elements and documentation (the soldering iron is not included)
Detailed description in EP 7/07
Download
193113
Manufacturer
- AVT SPV Sp. z o.o.
- Leszczynowa 11
- 03-197 Warszawa
- Poland
- [email protected]
Responsible person
- AVT SPV Sp. z o.o.
- Leszczynowa 11
- 03-197 Warszawa
- Poland
- [email protected]
Other products in the same category (16)
A wireless energy consumption monitor with built-in memory, thanks to the analysis of daily consumption, can help reduce the cost of water consumption
Retired
No product available!
Flex Cable for Raspberry Pi Camera - 200mm / 8". Adafruit 1647
Retired
No product available!
Useful for securely attaching a Pmod to your project or application; works with any Pmod 0.80" in width. 240-107
Retired
No product available!
MYIR MYC-C7Z010 is a single board module based on the MYC-C7Z010 chip. This system consists of a dual-core processor based on the Cortex-A9 core (667 MHz) and the Artix-7 FPGA chip. The board has 1 GB of DDR3 SDRAM, 4 GB of eMMC memory and 32 MB of QSPI Flash memory. The board is equipped with numerous peripherals, the outputs of which have been led out on two 140-pin connectors.
Retired
No product available!
No product available!
AVT kit for self-assembling LEDs, contains a set of elements. AVT1844 B
Retired
No product available!
Assembled AVT set, Christmas, shining Christmas tree LED. AVT1844 C
Retired
No product available!
The sensor detects dangerous carbon monoxide and carbon monoxide, signals a gas leak and the presence of carbon monoxide in rooms. URZ0409
Retired
No product available!
Female-female 10-core connection cable, 15 cm long with connectors of 1.27 mm pitch. Adafruit 1675
Retired
No product available!
No product available!
32GB microSDHC Memory Card with SD Adapter, class 4, Kingston
Delivery date unknown
No product available!
The Pmod TMP3 is an ambient temperature sensor built around the Microchip TCN75A. Users may configure the output through I2C to up to 12 bits of resolution as well as setting a trigger to occur when a user defined temperature threshold is reached.. Digilent 410-287
Retired
No product available!
The Pmod DHB1 uses DRV8833 dual H-Bridge motor driver chip to drive two DC motors or a single stepper motor. 410-259
Retired
No product available!
Development kit chipKIT DP32 equipped with PIC32MX250F128B microcontroller (40/50 Mhz, 128 kB Flash, 32 kB RAM), prototype area with solder pads, potentiometer, 4 LED diodes, 2 buttons and soldering pads for EEPROM memory and analog temperature sensor. Digilent 410-280P-KIT
Retired
No product available!
large 14x21 hole prototyping area on an expansion card compatible with the myRIO Expansion Port (MXP). 6002-210-008P
Retired
No product available!
The set of key components in the myParts Kit encourages hands-on experimentation with breadboards of basic circuitry, helping to make learning productive and enjoyable for beginners and more advanced students alike. Hobbyists and independent developers will also find the kit useful for investigating their design concepts. 6002-240-001P-KIT
Retired
No product available!
DIGITAL SOLDERING STATION RL1 - SELF-ASSEMBLY KIT