- Out-of-Stock
zł10,639.61
.png)
New products
New products New products
Rover 5 Robot Platform
ID: 201310
ROB-10336
Description
If you’re looking for a chassis base for your next robot, look no further than the Rover 5. The Rover 5 uses 4 independent motors, each with a hall-effect quadrature encoder and gearbox. The entire gearbox assembly can be rotated at 5 degree increments for different clearance configurations. You can even replace the tank treads with traditional wheels.
This isn’t a wimpy or flimsy robot base. Weighing in at over 2.5 pounds without batteries, this base is heavy duty and can drive over quite a bit. Check the manual below for dimensional drawings.
Features
- Adjustable gear box angles
- 4 independent DC motors
- 4 independent hall-effect encoders
- Thick rubber tank treads
- 6x AA battery holder
- 10Kg/cm stall torque per motor
Documents
201310
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł109.91
24h
Available quantity: 238
Available
DRV8825 Stepper Motor Driver Carrier with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. Pololu 2982
zł72.53
24h
Available quantity: 1
Available
This is a breakout board for ON Semiconductor’s AMIS-30543 microstepping bipolar stepper motor driver, which features SPI-adjustable current limiting, 11 step modes (from full-step through 1/128-step), back-EMF feedback that can be used for stall detection or optional closed-loop control, and over-current and over-temperature protection.
zł98.45
24h
Available quantity: 1
Available
Crawler platform equipped with DC motors. Made of aluminum alloy, it allows you to move efficiently on any surface. Assembly kit. DFRobot ROB0128
zł445.95
Delivery date unknown
No product available!
Other products in the same category (16)
Wireless motion sensor and magnetic field with built-in event memory (recorder)
Retired
No product available!
Wireless motion sensor and magnetic field with built-in event memory (recorder)
Retired
No product available!
Wireless, accurate temperature and humidity sensor with built-in event memory (recorder)
Retired
No product available!
Wireless, accurate temperature and humidity sensor with built-in event memory (recorder)
Retired
No product available!
Connection of 5MPx camera with JPEG compression with full BLE functionality
Retired
No product available!
The device allows the presence of devices with BLE in networks with Ethernet protocol, extends the range of sensors iNode Care Sensor
Retired
No product available!
A wireless energy consumption monitor with built-in memory, thanks to the analysis of daily consumption, can help reduce the cost of electricity consumption
Retired
No product available!
A wireless energy consumption monitor with built-in memory, thanks to the analysis of daily consumption, can help reduce the cost of water consumption
Retired
No product available!
Flex Cable for Raspberry Pi Camera - 200mm / 8". Adafruit 1647
Retired
No product available!
The extension cables let you locate Pmod 6" away from its host board, or use your 12-pin Pmod on a system board with only two 6-pin Pmod headers available. 240-021-2
Retired
No product available!
Useful for securely attaching a Pmod to your project or application; works with any Pmod 0.80" in width. 240-107
Retired
No product available!
MYIR MYC-C7Z010 is a single board module based on the MYC-C7Z010 chip. This system consists of a dual-core processor based on the Cortex-A9 core (667 MHz) and the Artix-7 FPGA chip. The board has 1 GB of DDR3 SDRAM, 4 GB of eMMC memory and 32 MB of QSPI Flash memory. The board is equipped with numerous peripherals, the outputs of which have been led out on two 140-pin connectors.
Retired
No product available!
No product available!
AVT kit for self-assembling LEDs, contains a set of elements. AVT1844 B
Retired
No product available!
Assembled AVT set, Christmas, shining Christmas tree LED. AVT1844 C
Retired
No product available!
The sensor detects dangerous carbon monoxide and carbon monoxide, signals a gas leak and the presence of carbon monoxide in rooms. URZ0409
Retired
No product available!
ROB-10336