- Out-of-Stock
AVT2736 B
ID: 193709
400 W AMPLIFIER - A SELF-ASSEMBLY KIT
400 W AMPLIFIER - A SELF-ASSEMBLY KIT
Producer: AVT
This amplifier was designed at the request of EdW readers. High output power, with a relatively low supply voltage, is possible due to the use of two power terminals connected in a bridge circuit (BTL). The presence of an input differential amplifier minimized the problems associated with running the system's mass.
Two heat sinks with fans were used as cooling - ready modules for cooling processors in a PC. Thanks to this, the entire system is characterized by relatively small dimensions. The amplifier can be used as a guitar stove.
The device is especially recommended for audiophiles and musicians-electronics
Selected parameters of the amplifier:
- peak power - up to 400 W (optionally 2x 100 W)
- delayed speaker connection system, mute after disconnecting the power supply
- active cooling (fans)
- load - 8 ohms
- power supply - 2x45 V
- set of components, printed circuit board and documentation included
- Detailed description in
Download
193709
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
Development kit chipKIT DP32 equipped with PIC32MX250F128B microcontroller (40/50 Mhz, 128 kB Flash, 32 kB RAM), prototype area with solder pads, potentiometer, 4 LED diodes, 2 buttons and soldering pads for EEPROM memory and analog temperature sensor. Digilent 410-280P-KIT
Retired
No product available!
large 14x21 hole prototyping area on an expansion card compatible with the myRIO Expansion Port (MXP). 6002-210-008P
Retired
No product available!
Perfect for connecting devices using Wi-Fi, Ethernet and Power over Ethernet options, the Yun combines an ATmega32u4 microcontroller with a Linux based Linino WiFi System on Chip module. A000003
Retired
No product available!
LPCXpresso4337 starter board with a dual-core LCP4337 microcontroller (Cortex-M4F + Cortex-M0 +). The set is equipped with a built-in programmer, buttons, diode, SPI Flash quad flash and USB - UART konwetrer
Retired
No product available!
Starter board LPCXpresso18S37 with LPC18S37 microcontroller (Cortex-M3). The set is equipped with a built-in programmer, buttons, diode, SPI Flash quad flash and USB - UART konwetrer
Retired
No product available!
Aluminum extensometer beam, allowing weight measurement up to 100 kilograms. It has four wires. It is used in kitchen scales and portable scales, max 100 kg, 20x23x94, 21 cm cable, RoHS
Retired
No product available!
High quality XF-ABS filament for 3D printer with 1.75 mm diameter. 1 kg of wire is wound on the spool. XF-ABS-175-GRAY
Retired
No product available!
The DDS generator with a readable alphanumeric display allows you to generate sinus, rectangular or triangle waveforms. The device can also be used for frequency measurement in the 1Hz-60MHz range
Retired
No product available!
ZigBee development/evaluation kit designed for CC2530F256
Retired
No product available!
Motor Control Shield, drives DC Motors & Stepping Motors
Retired
No product available!
EMW3162 WIFI Shield consists of a base plate and WiFi module EMW3162. Works with Arduino and STM32 Nucleo. Built-in USB-UART converter
Retired
No product available!
Music Shield for Arduino Development, Audio Play/Record, VS1053B Onboard
Retired
No product available!
BB Black Expansion CAPE, Supports Arduino, Compatible with UNO (default) and Leonardo (by configuration)
Retired
No product available!
100-MSPS USB Oscilloscope, Logic Analyzer and Variable Power Supply. 410-321
Retired
No product available!
100-MSPS USB Oscilloscope, Logic Analyzer and Variable Power Supply. 410-321
Retired
No product available!
This gearmotor is a powerful 12V brushed DC motor with a 18.75:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 64 counts per revolution of the motor shaft, which corresponds to 1200 counts per revolution of the gearbox’s output shaft. These units have a 16 mm-long, 6 mm-diameter D-shaped output shaft. This gearmotor is also available without an encoder.
Retired
No product available!
400 W AMPLIFIER - A SELF-ASSEMBLY KIT