- Out-of-Stock
Arduino Wireless Shield SD - overlay with Xbee socket
ID: 198334
A wireless overlay designed for Arduino tiles. Equipped with a connector compatible with Xbee modules and a microSD card slot. Arduino A000065
Description
Arduino Wireless Shield is a wireless communication overlay for Arduino tiles. Equipped with a connector compatible with Xbee modules and a microSD card slot. The switch on the board enables the wireless module to communicate with the USB-UART converter or microcontroller.
Attention!
The set does not contain the Xbee module and the Arduino board . They should be purchased separately.
properties
- Compatible with Arduino boards
- Compatible with Xbee modules
- MicroSD card slot
- Area with holes for prototypes
- Supply voltage 5 V
198334
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Cap for Xbee and Arduino. It has been designed for wireless sensor networks such as WiFi, Bluetooth 2.0 / 4.0 and Zigbee. DFRobot DFR0015
zł43.48
24h
Available quantity: 1
Available
RF module providing wireless communication compliant with the IEEE 802.15.4 standard. They operate in the 2.4 GHz ISM band and enable local configuration via BLE with the Digi XBee mobile application. They are equipped with the Silicon Labs EFR32MG SoC transmitter and receiver chipset. The range in buildings is up to 90 m, while in open space it reaches up to 3200 m. SparkFun WRL-22629
zł261.01
24h
Available quantity: 1
Available
Base board for prototyping IoT applications using the new Digi XBee 3 Low-Power LTE-M/NB-IoT and Digi XBee RR modules. It gives access to the full functionality of the XBee module pins, including two USB Type-C connectors for UART communication and firmware updates, a Qwiic connector for I2C-compatible sensors and peripherals. SparkFun WRL-21636
zł106.46
Delivery date unknown
No product available!
A base board that allows you to integrate modern Digi XBee 3 and Digi XBee RR Pro modules with the Arduino format, enabling you to build wireless projects. It uses a USB Type-C connector and a Qwiic connector to connect I2C sensors. SparkFun WRL-22131
zł60.20
24h
Available quantity: 1
Available
Other products in the same category (16)
SBC computer with Quad-Core ARM processor Samsung Exynos4412 (Cortex-A9 1.5GHz), 1GB RAM, LCD7 ", RoHS
Retired
No product available!
Graphic LCD 128x64, 75x52.8mm, FFSTN negative (white), KS108 controller, high contrast
Retired
No product available!
iNEMO inertial module: 3D accelerometer, 3D gyroscope, 3D magnetometer, ST, RoHS, LGA-24
Retired
No product available!
The assembled and activated module is designed to control differently colored LEDs. AVTMOD02
Retired
No product available!
No product available!
Kit: MAXimator, MAXimator Expander, ZL32PRG - USB Blaster PRO
Retired
No product available!
No product available!
hb03w-p-000-00
Delivery date unknown
No product available!
The eXtremestyle silicone cable (1.5m length) with US Type C connector. Allows you to charge the device and transfer data. eXtreme S15UCB
Retired
No product available!
No product available!
2.5 mm JST XH-Style Shrouded Male Connector: 2-Pin, Right Angle
Retired
No product available!
No product available!
Module with jack connector (TRS) and balanced line transmitter THAT 1646. Offers low distortion and high attenuation. SparkFun BOB-14002
Retired
No product available!
A development board that offers advanced programming and experimentation capabilities for smart device and industrial automation applications. It is based on the Rockchip RV1103 system, has an NPU unit and an ISP input. It offers a built-in USB port, GPIO and a microSD card slot. Waveshare Luckfox Pico M
Retired
No product available!
No product available!
No product available!
A wireless overlay designed for Arduino tiles. Equipped with a connector compatible with Xbee modules and a microSD card slot. Arduino A000065