- Out-of-Stock
PmodPMON1
Power Monitor, Digilent, RoHS
The PmodPMON1 employs the Analog Devices® AD5112 and ADM1191 to create a system power monitor.
Customers can configure the PMON1 to a wide range of possible alert conditions from the ADM1191 by using the configurable AD5112 potentiometer. The AD5112 upper potentiometer connection ties to DVDD through a filtering ferrite bead and the lower connection connects to GND. The wiper directly connects to the SETV pin on the ADM1191 to allow for the wide range of alert conditions. If an alert condition occurs, LD1 on the PMON1 will illuminate and the alert pin will go to a logic low state.
Key Features:
Contents:
Download:
Code: 210-265
Manufacturer
Responsible person
Development kit with STM32L496ZGT6 microcontroller (ARM Cortex-M4 core) with a built-in ST-Link programmer. Extensive equipment, including: MEMS 6DoF sensor, motor controller, joystick, LED display, 8 LED diodes, RGB LED, audio amplifier, Flash memory QSPI 1 MB, microphone, Arduino connector
Development kit with STM32L496ZGT6 microcontroller with built-in ST-Link programmer. Extensive equipment, including: MEMS 6DoF sensor, motor controller, joystick, LED display, 8 LED diodes, RGB LED, audio amplifier, Flash memory QSPI 1 MB, microphone.
Multifunctional tool for crimping connectors and coaxial connectors RG58, RG59, RG62, RG6, has a locking function and the ability to adjust the pressure. HT-301C
No product available!
Multifunctional tool for crimping insulated connectors on AWG 22-20 / 16-18 / 12-10 cable, has a locking function and the ability to adjust the pressure. HT-301E
No product available!
64-bit quad-core mini single board computer; features 2GB of RAM and 8GB eMMC; onboard WiFi and BT; 2 USB A 2.0 ports, 1 USB OTG port, 1 HDMI port, 1 audio jack, and lastly a DC power port
No product available!
Banana PI BPI-M2 Ultra is the open source hardware platform, Banana PI BPI-M2 Ultra is a quad-core cortex -A7 CPU ,use Allwinner R40 design, it support WIFI+BT on board.and support SATA interface on board
No product available!
The RASPBERRYPI-2-MODB-1GB is a second generation Raspberry Pi
No product available!
Waveshare camera module with OV7670 chip, 0.3 megapixels, resolution up to 640x480 pixels. It enables downloading of images in various formats via the Serial Camera Control Bus (SCCB) interface at 30 fps. Waveshare 9828
No product available!
Raspberry Pi 3 & MathWorks Learn to Program Pack is a set consisting of a Raspberry Pi 3 computer with necessary hardware and MATLAB & Simulink Student Suite software. The set is designed for modeling and implementing solutions based on Raspberry Pi 3 in MATLAB and SIMULINK environments
No product available!
IBM Watson IoT Platform is a set containing a computer Raspberry Pi 3 model B and Shield Raspberry Pi Sense HAT together with a course on modeling, simulation and analysis of projects related to Raspberry Pi 3 in IoT (Internet of Things) systems. PI3 IBM IOT LEARNKIT
No product available!
Battery: Li-Ion; 3.7V; 400mAh; Outputs: wires with 2-pin JST-PH connector; 50.8 mm x 33.5 x 5.9 mm. PRT-13851
No product available!
The GY-GPS6MV1 module is a board containing the U-blox NEO-6M GPS receiver system. The tile also includes RTC backup battery, antenna connector (U.FL), voltage stabilizer and UART signal outputs
No product available!
3DR Radio is a set that allows bidirectional transmission of telemetry data, eg between the RC model (with the APM controller) and a PC. Light and small device in a set with antennas and connecting cables. Radio modules have a power of 100mW (+ 20dBm) and transmit a signal over a distance of 1km.
No product available!
A small USB splitter allowing to connect up to 4 USB devices, powered from the USB port
No product available!
The Teensy is a breadboard-friendly development board with loads of features in a, well, teensy package. Each Teensy 3.2 comes pre-flashed with a bootloader so you can program it using the on-board USB connection: No external programmer needed! PJRC TEENSY32
No product available!
No product available!
This is the Teensy Audio board add-on for the Teensy 3.x line development boards. This audio board provides you with an easy-to-use tool to add high quality 16 bit, 44.1 kHz sample rate audio to your Teensy project. PJRC TEENSY3-AUDIO
No product available!
No product available!
Power Monitor