- Out-of-Stock
MULTIODORNIK ELF-VLF - POWER SUPPLY SYMETRATION SYSTEM - PLATE PCB
Producer: AVT
The ELF-VLF receiver, or rather a set of receivers, enables reception of mysterious radio signals with extremely low frequencies. It is possible to observe signals of communication with submarines and so-called Schumann resonance.
It is possible only in extra-urban conditions (eg during trips), and this is due to the high level of industrial disturbance in cities. In the city, the described systems can be used, for example, to observe storms and the level of industrial disturbances. Such their use can also be very interesting. A lot of information about the reception of electromagnetic waves at very low frequencies, below 30kHz, as well as about antennas used for this type of receivers, is provided in the article 'Receiving ELF-VLF radio waves'.
The project presents four receivers, designed to receive radio signals (electromagnetic waves) in the range from 3Hz to 30kHz, thus including bands: ELF, SLF, ULF and VLF. The first of the receivers (I) cooperates with a wire antenna, reacting to the electrical component of the electromagnetic field. It was made in two system versions (Ia and Ib). The third and fourth are designed to cooperate with a loop antenna, reacting to the magnetic component of the electromagnetic field. The article also describes the system generating symmetrical power supply voltage and systems improving work comfort by increasing resistance to unwanted signals: two low-pass filters with band respectively 200Hz and 20kHz, bandpass filter, reducing the hum of 50Hz and optoisolator m signals .cz. The described systems do not require tuning or startup, so that even a novice electronics can do it. The big advantage of these systems is the low cost of their implementation.
Note: the project has been divided into 6 parts:
AVT3054 / 4
The receivers (AVT3054 / 1, AVT3054 / 2, AVT3054 / 3) should be supplied with symmetric voltage from a pair of batteries or accumulators or by means of an 'artificial mass' generating system. The use of such a symmetrical power supply significantly simplifies the construction of the systems. If you need to use a power supply other than battery or battery power, you should carefully choose the system solution. It should be remembered that all switched-mode power supplies and DC / DC converters are sources of voltage disturbances that are too strong to be used directly.
Includes AVT3054 / 4 printed circuit board and documentation.
Detailed description in EdW3 / 13 or ![]()
Additional materials:
Article 'ELF-VLF radio reception' from the journal Elektronika Dla Wszystkich 10/2011
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
DC-DC Step-Down converter module with an output voltage of 3.3V and a current efficiency of 3A. The module is based on the MP2307DN chip.
No product available!
The AI accelerator with a USB connector is based on the Lightspeeur SPR2801S chip with a performance of up to 9.3 TOPS per watt. Optimized for use with single board computers based on Allwinner SoC chips, incl. Orange Pi. Orange Pi AI Stick Lite
No product available!
2-channel module with 12V relays and a radio receiver in a set with a remote control operating at 433 MHz
No product available!
Set with HQ camera, HDMI adapter, lens, tripod. Designed for NVIDIA Jetson Nano and Xavier NX. ArduCAM B0250
No product available!
CraftBot FLOW 3D printer made of the highest quality components, with a filament sensor, semi-automatic calibration and wireless connectivity. Thanks to its intuitive operation, the printer will be perfect for both professionals and beginners
No product available!
CraftBot FLOW XL 3D printer made of the highest quality components, with a filament sensor, semi-automatic calibration and wireless connectivity. Thanks to its intuitive operation, the printer will be perfect for both professionals and beginners. XL version with increased print area
No product available!
CraftBot FLOW IDEX 3D printer made of the highest quality components, with a filament sensor, semi-automatic calibration and wireless connectivity. Thanks to its intuitive operation, the printer will be perfect for both professionals and beginners
No product available!
CraftBot FLOW IDEX 3D printer made of the highest quality components, with a filament sensor, semi-automatic calibration and wireless connectivity. Thanks to its intuitive operation, the printer will be perfect for both professionals and beginners
No product available!
The case is made of ABS plastic (black) with a built-in fan, designed for Raspberry Pi 4 model B. The case provides access to all connectors of the minicomputer.
No product available!
Portable 7" monitor with touch screen. The monitor is equipped with HDMI interface for image display and USB for touch screen. High resolution 1920x1080 pixels. Waveshare 7inch FHD LCD
No product available!
15.6" portable touch screen monitor. The monitor is equipped with HDMI interface for image display and USB Type-C for image display and touch screen. High resolution 1920x1080 pixels. Waveshare 15.6inch FHD LCD (for EU)
No product available!
No product available!
No product available!
MicroHDMI - HDMI cable in white color, 2 meter long. Intended for use with Raspberry Pi 4 model B.
No product available!
3.2" LCD TFT display with touch screen. The display is equipped with an SPI interface for image display and touch screen operation. Resolution 320x240 pixels. Waveshare 3.2inch RPi LCD (C)
No product available!
IPS 4" LCD display with touch screen. The display is equipped with DPI interface for image display and I2C interface for touch screen. Resolution 800x480 pixels. Waveshare 4inch DPI LCD (B)
No product available!
MULTIODORNIK ELF-VLF - POWER SUPPLY SYMETRATION SYSTEM - PLATE PCB