- Out-of-Stock
5V stabilizer with 500mA protection
ID: 557549
The stabilizer module is used to stabilize the output voltage at an appropriate level and filter interference. The module can be supplied with voltage up to + 16V, and the output voltage is + 5V. MOD-06 / 5V.Z
Description
Electronic devices require power with a certain voltage value. The stabilizer is used to stabilize the output voltage at an appropriate level and filter interference. The module can be supplied with voltage up to + 16V, and the output voltage is + 5V.
For example, if a voltage stabilizer is connected to the + 12V power supply, then on its output we get + 5V (other voltage values are also available) that we can use to power the microcontroller.
The module has a built-in protection of 500mA. If the current exceeds this value, the fuse will operate and the output will be disconnected. In this case, just disconnect the power supply to reset the protection, there is no need to replace the fuse.
Technical data
- Integrated circuit: LM7805
- Protection: 500mA polymer fuse
- Power: up to + 16V
- Output voltage: + 5V
- LED signaling: yes
- Additional information: built-in filter capacitors for higher load currents and a large difference between the supply voltage and the output voltage, it may be necessary to use a heat sink for heat dissipation
- Dimensions: 39 x 16 mm
- RoHS: yes
Set contains
- Assembled MOD-06 / 5V.Z 5V stabilizer with protection
- A set of connectors for self-assembly (ARK screw connection - 2 pcs)
To download
557549
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
No product available!
No product available!
No product available!
High quality acrylic computer case for Orange Pi One, transparent
Retired
No product available!
No product available!
TEST PLATE FOR BASCOM AVR COURSE MICROPROCESSOR COIL JOINT - A KIT FOR INDEPENDENT INSTALLATION
Retired
No product available!
ZP120.120.60UUJH TM ABS - Hermetic housing ZP120.120.60 light with ears with seal and brass bushings ABS
Retired
No product available!
Module cooperating with Arduino Ethernet Shield 2 and Arduino Ethernet. It allows you to connect power to Arduino from an Ethernet network. Compliant with the IEEE 802.3af Power-over-Ethernet standard.
Retired
No product available!
Development board with an ESP32 module based on a 32-bit Xtens LX6 processor. It has been equipped with a number of peripheral systems such as RGB LED matrix, accelerometer, magnetometer, gyroscope, light sensors and programmable buttons. Banana Pi BPI-Bit
Retired
No product available!
Filament from ROSA3D made of high-quality PLA pellets. Placed on a cardboard thimble, on which 1 kg of 1.75 mm diameter filament is wound. ROSA3D ReFill PLA Starter Green
Retired
No product available!
No product available!
Off-road Dagu Wild Thumper 4WD chassis in silver, complete with wheels with a diameter of 120 mm and motors with a 34:1 gearbox. The chassis is made of aluminum sheet, holes with a diameter of 4 mm spaced every 10 mm allow the installation of the controller and accessories. Pololu 1564
Retired
No product available!
No product available!
No product available!
Miniature vacuum pump powered by 12 V. Generates a vacuum that can be used, for example, in robotics
Retired
No product available!
No product available!
The stabilizer module is used to stabilize the output voltage at an appropriate level and filter interference. The module can be supplied with voltage up to + 16V, and the output voltage is + 5V. MOD-06 / 5V.Z