- Out-of-Stock
MYIR MYC-C7Z010 CM
ID: 560458
MYIR MYC-C7Z010 is a single board module based on the MYC-C7Z010 chip. This system consists of a dual-core processor based on the Cortex-A9 core (667 MHz) and the Artix-7 FPGA chip. The board has 1 GB of DDR3 SDRAM, 4 GB of eMMC memory and 32 MB of QSPI Flash memory. The board is equipped with numerous peripherals, the outputs of which have been led out on two 140-pin connectors.
Description
MYIR MYC-C7Z010 is a single board module based on the MYC-C7Z010 chip. This system consists of a dual-core processor based on Cortex-A9 core that can operate at a maximum frequency of 667 MHz and Artix-7 FPGA. The board is equipped with 1 GB of DDR3 SDRAM, 4 GB of eMMC memory and 32 MB of QSPI Flash memory. The board has numerous peripherals: 10/100/1000 ethernet, external Watchdog or LED diodes. The GPIO outputs, ADC USB OTG 2.0 inputs and interfaces (Serial, I2C, SPI, CAN BUS) have been output on two 140-pin connectors.
properties
- SOC - XC7Z010 (Xilinx Zynq-7010/7020)
- Dual core processor based on Cortex-A9 (667 MHz)
- Integrated Artix-7 FPGA
- 28 thousand logical cells, 17600 LUT, 80 DSP patches (for XC7Z010)
- 85 thousand logical cells, 54200 LUT, 220 DSP patches (for XC7Z020)
- Memory:
- 1 GB of DDR3 SDRAM (2 x 512 MB)
- 4 GB of eMMC memory
- 32 MB QSPI Flash memory
- Periphery:
- Ethernet 10/100/1000
- External Watchdog
- Three LEDs
- Power status (blue)
- Signaling work of FPGA (red)
- Available to the user (green)
- Two 140-pin connectors (0.8 mm pitch) with pins:
- Gigabyte Ethernet
- USB OTG 2.0
- Two serial ports
- Two I2C
- Two CAN BUS
- Two SPI
- ADC
- SDIO
- Supported system: Linux 3.15.0
- Supply voltage: 5 V (0.5 A)
- Dimensions: 75 x 55 mm
560458
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
CuteDuino Attiny85 - module with Attiny85 microcontroller
Retired
No product available!
No product available!
Extends use support contract for access to software updates and direct support for one additional year.
Retired
No product available!
Adafruit 659 - FLORA - Wearable electronic platform: Arduino-compatible - v2
Retired
No product available!
This gearmotor consists of a low-power, 6 V brushed DC motor combined with a 4.4:1 metal spur gearbox, and it has an integrated 48 CPR quadrature encoder on the motor shaft, which provides 211.2 counts per revolution of the gearbox’s output shaft.
Retired
No product available!
CLOCK CONTROLLER AND NOT ONLY - PRINTED PLATES AND PROGRAMMED SYSTEM - PLATE AND PROGRAMMED LAYOUT
Retired
No product available!
No product available!
Do you fly in your dreams? Do you like the feeling? Once again Ugears makes the dream come true reaching out to the sky with its first ever aircraft model represented by two flying machines in one package. Introducing – The Aviator model.
The model has three modules: the airplane, the helicopter and the flight control tower. Choose between your aircraft, set one on the tower’s bar and you are good to fly. As a beginner pilot you might want to start with the helicopter which is not as difficult to control as the airplane. Easier to manipulate but no less exciting, your chopper has a cockpit with doors that open and shut, and three-blade main and tail rotors. UGears 70053
Retired
No product available!
MYIR MYC-C7Z010 is a single board module based on the MYC-C7Z010 chip. This system consists of a dual-core processor based on the Cortex-A9 core (667 MHz) and the Artix-7 FPGA chip. The board has 1 GB of DDR3 SDRAM, 4 GB of eMMC memory and 32 MB of QSPI Flash memory. The board is equipped with numerous peripherals, the outputs of which have been led out on two 140-pin connectors.