zł99.90
New products
New products New products
Pimoroni Pico LiPo 2 development board – RP2350B, 16MB Flash, 8MB PSRAM, USB-C, LiPo, Qw/ST – PIM775
zł109.74
24h
Available
zł153.64
24h
Available
zł75.41
24h
Available
Available
Available
OM26630FDK - NFC evaluation kit with CLEV6630B board
ID: 580272
zł799.00
Tax included
zł649.59 tax excl.
A development kit designed for NFC applications. It includes the CLEV6630B board based on the LPC1769 microcontroller, NFC cards and a set of antennas. NXP OM26630FDK
Description
A development kit designed for NFC applications. It includes the CLEV6630B board based on the LPC1769 microcontroller, NFC cards and a set of antennas for EMVCo (card payment standard) and access management applications. A dedicated NFC Reader Library is available for operation.
The CLEV6630B board is fitted with a metal layer 65 x 65mm antenna by default to demonstrate CLRC663 performance and setup under typical design constraints such as LCD or metal (eg PCB) inside the antenna area. An additional 30 x 50 mm antenna and three small antennas allow for the implementation of a custom antenna matching circuit.
Features
- LPC1769 microcontroller
- SPI interface for connecting other MCU
- Low-Power card detection mode
- Good RF performance
- Artificial RF field suppression in the center of the antenna, simulating the presence of a PCB or display to demonstrate the expected performance
- Compliance with all standards for the operation of the NFC proximity reader and EMVCo 2.6
Kit contains
- CLEV6630B board
- NFC antenna 30x50mm
- 3 x small PCB antenna
- 2 x NFC card
- 10 x CLRC663 plus chip in HVQFN package
580272
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Cable with USB typ A and microUSB typ B connectors, cable length 1 m. LANBERG CCP-MUSB2-AMBM-W-1M
zł3.21
24h
Available quantity: 27
Available
Cable with USB typ A and microUSB typ B connectors, cable length 1.8 m. LANBERG CA-USBM-10CC-0018-BK
zł4.00
24h
Available quantity: 10
Available
Cable with USB typ A and microUSB typ B connectors, cable length 1.8 m. LANBERG CA-USBM-10CC-0018-W
zł3.49
24h
Available quantity: 18
Available
Other products in the same category (16)
Demo kit for prototyping applications and devices based on NFC ST25DV64KC tags. STMicroelectronics ST25DV64KC-DISCO
zł377.81
24h
Available quantity: 4
Available
The RFID / NFC transponder reader module (tags) works in the PN532 chip and is compatible with Arduino. Data is available via SPI, I2C or HSU (High Speed UART). Supplied with a RFID card and key ring. ELECHOUSE NFC MODULE V3
zł29.93
24h
Available quantity: 269
Available
NFC reader with USB interface. It allows you to easily read data from an NFC/RFID card using a computer
zł109.75
24h
Available quantity: 2
Available
Module with an RFID reader designed to work with the Raspberry Pi Pico. Equipped with an OLED display and a buzzer. SB Components 21192
zł140.65
24h
Available quantity: 2
Available
Intelligent RFID identifier cooperating with iNode Control Point
zł101.84
24h
Available quantity: 1
Available
A set of RFID tags consisting of three key rings in different colors and two white cards. The tags operate at 125 kHz and comply with the EM4100 standard. Seeed Studio 110990035
zł14.34
24h
Available quantity: 2
Available
Adafruit 789 - Adafruit PN532 NFC/RFID Controller Shield for Arduino + Extras
zł235.56
24h
Available quantity: 1
Available
A module with an NFC PN532 transceiver, which supports proximity communication at the frequency of 13.56 MHz. The board is equipped with a Grove connector and communicates via the I2C or UART interface. Seeed Studio 113020006
zł97.67
24h
Available quantity: 5
Available
RFID identification key with dimensions of 40.5 mm x 32 mm x 4.2 mm, operating on the 13.56 MHz frequency. RFID Tag Key
zł1.50
24h
Available quantity: 142
Available
The 13.56 MHz RFID reader module in a set with a keyring and RFID card
zł9.85
4 weeks
No product available!
The module for the RFID reader (125 kHz) is equipped with a USB interface. Works with ID-3LA, ID-12LA and ID-20LA series systems. The selected RFID reader is simply plugged into the module\'s connectors. SparkFun SEN-09963
zł132.46
24h
Available quantity: 1
Available
Card with RFID tag for systems operating at 125 KHz. Provides the ability to read and write the ID number
zł2.87
24h
Available quantity: 26
Available
Available
Module with RFID 125 KHz tag reader. It allows reading 125KHz RFID tags / cards (EM4100 standard) from a maximum distance of 7 centimeters. The module has a connector in accordance with the Grove standard. Seeed Studio 113020002
zł64.55
24h
Available quantity: 8
Available
Module with an RFID tag based on the ST25DV16K chip. It can be reprogrammed via the I2C bus. Equipped with STEMMA QT connector and PCB antenna. Adafruit 4701
zł19.91
4 weeks
No product available!
No product available!
A development kit designed for NFC applications. It includes the CLEV6630B board based on the LPC1769 microcontroller, NFC cards and a set of antennas. NXP OM26630FDK