- Out-of-Stock
Breakout for LinkIt Smart 7688 v2.0 - base board
ID: 563901
Breakout for LinkIt Smart 7688 v2.0 is a new version of the base board for the IoT LinkIt Smart 7688 module. Ethernet socket, USB Host socket, 3 Grove standard connectors (2 UART interfaces, I2C interface). Seeed Studio 103100022
Description
Breakout for LinkIt Smart 7688 v2.0 is a new version of the base board for IoT LinkIt Smart 7688 module (in this version it is possible to record sound). The tile contains, among others Ethernet socket, USB Host socket, 3 Grove standard connectors (2 UART interfaces, I2C interface). The set does not include the LinkIt Smart 7688 module module .
properties
- 3.5 mm jack socket (headphones / AUX + microphone)
- WM8960 stereo codec
- Ethernet socket
- USB 2.0 socket
- Grove connectors: 2 x UART, 1 x I2C
- Power supply: 5 V (USB socket)
- Logic level: 3.3 V
563901
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Linklt Smart 7688 is an IoT module with WiFi interface based on the MediaTek MT7688 system operating under the control of the distribution of the Linux operating system derived from OpenWrt. LinkIt Smart 7688 is a great base for creating complex IoT projects or a smart home. Seeed Studio 102110018
zł135.15
24h
Available quantity: 1
Available
Other products in the same category (16)
No product available!
Tomasz Starecki
The book in the form of an e-book can be bought here:
Retired
No product available!
No product available!
No product available!
No product available!
VNH3SP30-E, Automotive Fully Integrated H-Bridge Motor Driver, MultiPowerSO-30
Retired
No product available!
No product available!
A 10-bit programmable magnetic object rotation sensor (encoder). It can work at 3.3V and 5V, it has a measurement resolution of 0.35 degrees and a serial and PWM signal output. The system has a SSOP16 housing
Retired
No product available!
The P-NUCLEO-IOM01M1 is an STM32 Nucleo pack composed of the STEVAL-IOM001V1 and the NUCLEO-F446RE board. The STEVAL-IOM001V1 is a single IO-Link master PHY layer (L6360) while the NUCLEO- F446RE runs an IO-Link stack rev 1.1
Retired
No product available!
MYIR MYC-JA5D44 is a single-board computer in the form of a card with SO-DIMM 200-pin connector. The SAMA5D44 processor from Atmel, based on Cortex-A5 cores, has been equipped. It can work with a maximum frequency of 600 MHz. It has 512 MB of DDR2 SDRAM, 512 MB of NAND Flash memory. GPIO ports, interfaces have been derived on the SO-DIMM 200-pin connector.
Retired
No product available!
No product available!
No product available!
HK Turnigy nano-tech 4500mah 3S 25~50C Lipo Pack (11931)
Retired
No product available!
Scale module with aluminum tensometer beam, allowing weight measurement up to 2 kilograms. It has screw terminals. Can be used to make electronic scale. KAmodTENSOMETER2kg
Retired
No product available!
AVT kit for self-assembly of a siren for emergency vehicles. AVT789 B
Retired
No product available!
No product available!
Breakout for LinkIt Smart 7688 v2.0 is a new version of the base board for the IoT LinkIt Smart 7688 module. Ethernet socket, USB Host socket, 3 Grove standard connectors (2 UART interfaces, I2C interface). Seeed Studio 103100022