Adafruit ItsyBitsy 32u4 - 3V 8MHz - compatible with Arduino
ID: 569358
5906623470143
zł65.08
Tax included
zł52.91 tax excl.
Small development kit with ATmega32u4 microcontroller. The board has 6 power, 6 analog and 17 digital pins, which makes it have similar capabilities to the Arduino UNO. Compatible with Arduino. Adafruit 3675
Description
The ItbisBitsy 32u4 Adafruit plate is a small development kit with ATmega32u4 microcontroller. The board has 6 power, 6 analog and 17 digital pins, which makes it have similar capabilities to the Arduino UNO. In addition, the module contains 2 special pins: Vhigh, which leads to higher voltage from USB or battery, and digital output # 5, which is connected by a logic level converter. The plate is compatible with Arduino .
properties
- ATmega32u4 microcontroller in QFN housing
- Operating voltage: 3.3 V
- 8 MHz clock
- 2 KB RAM memory
- FLASH memory with a capacity of 28 KB
- USB bootloader with LED indicator, compatible with AVR109
- Micro USB connector for power supply as well as programming and debugging the system,
- It can work as an HID keyboard, mouse, MIDI or USB CDC device
- Built-in 3.3V stablilizer with 500 mA capacity and low dropout. Up to 6 V input voltage, reverse polarity protection, thermal and overload protection
- Possibility to power from a USB or external source (eg batteries)
- A special Vhigh pin for higher voltage from USB or battery. It can be used to control RGB diodes, servos or other devices that require more electricity
- Digital output # 5 connected by a logic level converter
- General purpose LED
- 23 GPIO lines - 6 analog inputs, SPI port, I 2 C, hardware serial port, and 10 other pins, including 4 x PWM
- Reset button
- Dimensions: 35 x 18 mm (1.4 "x 0.7")
569358
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Easy-to-use retractable cable with USB type A plugs and micro-B type, the cable has a length of 73 cm
zł9.90
Delivery date unknown
No product available!
Small development kit with ATmega32u4 microcontroller. The board has 6 power, 6 analog and 17 digital pins, which makes it have similar capabilities to the Arduino UNO. Compatible with Arduino. Adafruit 3677
zł51.45
24h
Available quantity: 2
Available
Other products in the same category (16)
Function module designed for MicroMod boards. It allows you to add LoRa and LoRaWAN wireless communication in the 915 MHz frequency band to the project. SparkFun DEV-18573
zł245.27
3 weeks
No product available!
Function module designed for MicroMod boards. It combines the SGP40 (air quality), SHTC3 (temperature and humidity) and STC31 (CO2 concentration) sensors and communicates via the I2C interface. SparkFun DEV-18632
zł1,163.27
3 weeks
No product available!
Function module designed for MicroMod boards. It allows you to add WiFi wireless communication based on the DA16200 chip to the project. SparkFun WRL-18594
zł161.66
24h
Available quantity: 1
Available
Function module designed for MicroMod boards. It allows you to add WiFi wireless communication based on the ESP32 chip to the project. SparkFun WRL-18430
zł87.86
24h
Available quantity: 1
Available
Extension board designed for MicroMod main modules. Equipped with the ZED-F9P GNSS receiver. It can receive data from GPS, GLONASS, Galileo and BeiDou systems. SparkFun DEV-17722
zł2,563.76
3 weeks
No product available!
Development board with WiFi and Bluetooth ESP32 module. It has been equipped with industrial interfaces RS485 and CAN. TTGO T-CAN485 ESP32
zł91.24
4 weeks
No product available!
Mini board with RP2040 microcontroller equipped with two ARM Cortex-M0 + 133 MHz cores, 264 kB RAM. The board also has 8 MB of QSPI flash memory. The circuit can be programmed in C/C++, CircuitPython or MicroPython. Pimoroni SP011
zł85.02
4 weeks
No product available!
The base plate is dedicated to the RP2040 Stamp module. It allows you to easily prototype devices based on RP2040. Pimoroni SP012
zł42.96
24h
Available quantity: 3
Available
Module with PM2.5 dust sensor. The board is equipped with a Gravity connector and communicates via the I2C interface. DFRobot SEN0460
zł202.34
4 weeks
No product available!
A set with a radio transmitter and receiver operating at 433 MHz. The modules are equipped with Gravity connectors and communicate via a digital interface. DFRobot TEL0140-1
zł59.97
24h
Available quantity: 1
Available
Radio transmitter module operating at 433 MHz. It is equipped with Gravity connectors and communicates via a digital interface. DFRobot TEL0140
zł30.55
24h
Available quantity: 3
Available
Radio receiver module operating at 433 MHz. It is equipped with Gravity connectors and communicates via a digital interface. DFRobot TEL0142
zł34.65
24h
Available quantity: 3
Available
Module with DHT20 temperature and humidity sensor. It allows you to measure humidity in the range from 0 to 100% and temperature from -40 to 80℃. DFRobot SEN0497
zł33.59
24h
Available quantity: 3
Available
An expansion board designed for FireBeetle M0 and ESP32-E kits. The board has 12 GPIO pins, 5 ADC, UART, I2C and SPI interfaces. The pins are color coded according to the Gravity standard. DFRobot DFR0762
zł20.52
24h
Available quantity: 2
Available
UART-RS485 converter module based on the TD (H) 541S485H chip. Equipped with power isolation and TVS. DFRobot DFR0845
zł89.26
24h
Available quantity: 3
Available
A miniature board with dimensions of 20x22 mm with an ATmega32U4 microcontroller. Compatible with Arduino Leonardo. DFRobot DFR0816
zł56.88
24h
Available quantity: 2
Available
Small development kit with ATmega32u4 microcontroller. The board has 6 power, 6 analog and 17 digital pins, which makes it have similar capabilities to the Arduino UNO. Compatible with Arduino. Adafruit 3675