Expansion board X-NUCLEO-6180A1 equipped with a VL6180 distance sensor, based on ST FlightSense technology. This is a breakthrough technology that allows you to measure the absolute distance regardless of the reflection of the target. The VL6180 accurately measures the time it takes for light to reach the nearest object and bounce back to the sensor (Time of Flight). The set is designed to measure distances and detect gestures.
Up to three VL6180-SATEL boards can be attached to the X-NUCLEO-6180A1 expander.

Attention!
VL6180-SATEL boards are not included. They must be purchased separately.The expansion board is compatible with the STM32 Nucleo family of boards and the Arduino Uno Rev3 connector system. The manufacturer provides an API library for sensor support.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
STM32 Nucleo development board for STM32 F4 series - with STM32F401RE MCU, 512KB flash memory, STM, RoHS
STM32 Nucleo development board for STM32 L0 series - with STM32L053R8 MCU, 64KB flash memory, STM, RoHS
No product available!
KAmodVL6180X is a module that allows to measure light intensity (ALS), distance to the object and recognition of gesture. It has an embedded voltage regulator and voltage level translators on signal lines. Thanks to this can be used in systems with 2.8...5.5V power supply voltage.
The STEVAL-FKI868V2 evaluation board is based on the S2-LP sub-1GHz ultra-low power low data-rate transceiver suitable for ISM bands and wireless M-Bus. The NUCLEO-L053R8 motherboard is equipped with an STM32L0 low power microcontroller to control the S2-LP
This sensor is a carrier/breakout board for ST’s VL6180X proximity and ambient light sensor, which measures the range to a target object up to 20 cm away (or 60 cm with reduced resolution). Pololu 2489
The set consists of the STM32 NUCLEO-F401RE board with the STM32F401RE microcontroller and the X-NUCLEO-53L3A2 board with the VL53L3CX distance sensors operating in ToF technology. STMicroelectronics P-NUCLEO-53L3A2
Multifunctional expander (shield) for NUCLEO and Arduino equipped with Bluetooth 2.0+EDR (HC-05) interface, MEMS 3DoF LIS35, LED-RGB, joystick and analog STLM20 temperature sensor developed and produced by KAMAMI.
Extension board for SMT332 Nucleo with VL6180X sensor, allowing to measure ambient lighting, zoom and recognition of gestures. On the PCB, outside the sensor, there is also a four-digit LED display and connectors for additional sensors
KAmodNFC is an expansion board with M24LR64E-R chip – dynamic tag with 64kb EEPROM memory and dual communication interface (I2C/RF). On board is placed also signalization of energy harvesting function, which is in M24LR64E-R chip embedded.
X-NUCLEO-IDS01A4 is a development board STM32 Nucleo that allows the use of the RF SPSGRF-868 module for the ISM band (868 MHz carrier).
X-NUCLEO-IDS01A5 is a development board STM32 Nucleo that allows you to use the RF SPSGRF-915 module on the ISM band (915 MHz carrier).
No product available!
The X-NUCLEO-IHM03A1 plate allows the control of a high-power stepper motor; the maximum current of the phase is 10A rms, additionally the controller enables execution up to 1/128 step and has a number of protections. X-NUCLEO-IHM03A1
Shield for STM32 Nucleo that allows you to add the possibility of operating a three-phase brushless motor (BLDC) or synchronous permanent magnet (PMSM). It uses the L6230 chip for control. X-NUCLEO-IHM07M1
Extension board X-NUCLEO-IHM04A1 for STM32 Nucleo, with dual brush motor controller, operating based on the L6206 system
The STM32 Nucleo expansion board allows you to control a bipolar stepper motor. The maximum phase current is 2.8A RMS, the controller has overheat protection and overcurrent protection
Industrial input/output expansion board based on VNI8200XP and CLT01-38SQ7 for STM32 Nucleo
No product available!
Multifunctional board for STM32 NUCLEO, built based on operational amplifiers. Has, among others built-in LED current controller, prototype area and window discriminator
Expander (shield) compatible with Arduino and NUCLEO (STM32) systems, equipped with a Bluetooth 4.1 (BLE) radio module from the SPBTLE-RF family
Shield for STM32 series Nucleo, XNucleo and Arduino series for communication via RS485 and CAN interfaces (CAN is only available for Nucleo and XNucleo plates). Shield is based on MAX3485 and SN65HVD230 systems
Two axis stepper motor driver expansion board based on the L6470 for STM32 Nucleo
Sound terminal expansion board based on STA350BW for STM32 Nucleo
No product available!
DC-DC LED driver expansion board based on LED6001 for STM32 Nucleo
Expansion board equipped with VL6180 distance sensor, based on FlightSense technology. The set is designed to measure distances and detect gestures. X-NUCLEO-6180A1