SEN-12784 SparkFun ToF Range Finder Breakout - VL6180
Description:
This is the SparkFun “Time-of-Flight” Range Finder, a breakout for the VL6180 distance sensor. Unlike most distance sensors that rely reflected light intensity or reflected angles to determine range, the VL6180 uses a precise clock to measure the time it takes light to bounce back from a surface. This affords the ToF Range Finder and VL6180 a great benefit over other methods because it can be much more accurate and more immune to noise. Does this technology sound familiar? Well it should, it’s the same means cellphones use to detect when the caller is holding their phone to their ear.
This breakout for the VL6180 is as simple as it gets. Only the required passives are populated to give you the smallest, most cost effective way to use multiple sensors in a project with an I2C interface. The VL6180 is actually a 3-in-1 package that combines an IR emitter, a range sensor, and an ambient light sensor together for you to easily use. We’ve broken out each pin that is required to use the VL6180, including: IO1, IO0, SCL, SDA, 2.8 V, and GND. Please be sure to note, however, the ToF Range Finder Breakout only accepts 2.8V input and logic. You must provide a 2.8 V voltage source and level shifting to 3.3 V and 5 V devices.
Note: Though the datasheet states the VL6180 measures an absolute range of up to 10cm, we have successfully tested it up to 25 cm. The more you know.
Features:
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
This sensor is a carrier/breakout board for ST’s VL53L0X laser-ranging sensor, which measures the range to a target object up to 2 m away.
VL53L0X ToF Laser Range Finder is a laser distance sensor using the ToF (Time of Flight) measurement technique. The module is supplied with 3.3 ... 5 V voltage and can measure up to 2 m. DFRobot SEN0245
No product available!
Distance sensor module operating in TOF technology, operating range 4-400 cm, resolution up to 1 mm. Communication with the sensor via the I2C bus. Power supply through a built-in regulator with voltage from 2.6 to 5.5 V. Pololu 3415
Ultrasonic distance sensor MB1040 with a range from 0 to 645 cm. It has an output in the form of a serial interface, analog signal or generates an impulse whose duration is proportional to the measured distance. Pololu 794
No product available!
The HC-SR04 ultrasonic sensor module is commonly used in conjunction with Arduino to precisely measure distances ranging from 2 cm to 500 cm, with a resolution of 3 mm. It is a good choice for projects in the field of robotics, automation and security systems. It works on the principle of emission and reception of ultrasonic waves. It works with microcontroller platforms such as Arduino, Raspberry Pi, ESP32 or STM32. modHC-SR04
No product available!
No product available!
No product available!
URM04 v2.0 Ultrasonic Sensor
Distance Measuring Sensor Unit; Measuring distance: 100 to 550 cm; Analog output type, Sharp, RoHS
No product available!
No product available!
The ultrasonic distance sensor modUS-015 is based on the analysis of the delay of reflection of the ultrasonic wave from the obstacle - the range of the sensor from 2 to 400 cm with an accuracy of 0.3 cm + 1%
No product available!
No product available!
A multifunctional module with an optical sensor for measuring the intensity of illumination, the color of the incident RGB light, the distance from the object and the detection of 3D gestures. Detection range from 10 to 20 cm, communication via I2C. SparkFun SEN-12787
Recognizes the distance of an object away from the sensor up to about 10 inches (~25cm) and the location of the object from side to side across the sensor in about a 6 inch (~15cm) span. You will be able to use I2C or UART to communicate with the ZX Sensor via an Arduino-based microcontroller as well as a computer. SEN-12780
No product available!
KAmodVL6180X is a module that allows to measure light intensity (ALS), distance to the object and recognition of gesture. It has an embedded voltage regulator and voltage level translators on signal lines. Thanks to this can be used in systems with 2.8...5.5V power supply voltage.
The GP2Y0A60SZ offers a wide detection range of 4″ to 60″ (10cm to 150cm) and a high update rate of 60Hz. The distance is indicated by analog voltage - only a single analog input is required to interface with the module. Pololu 2476
Suitable for outdoor applications such as car reversing sensors, security alarms, industrial inspection, etc. SEN0207
SEN-12784