Category: STARTER KITS, PROGRAMMERS, MODULES

Module with WiFi and Bluetooth Espressif ESP32 WROOM. It integrates a set of peripherals - capacitive touch sensors, Hall sensors, SD card interface, Ethernet, SPI, UART, I2S and I2C. SparkFun WRL-20168

Module with GNSS MAX-M10S receiver. It can receive signals from GPS, GLONASS, BeiDou and Galileo constellations. It has an SMA connector for connecting an external antenna and a Qwiic socket. SparkFun GPS-18037

LiPo battery monitor module based on the MAX17048 chip. Allows the voltage and state of charge of the battery to be measured. SparkFun SPX-17715

Red mounting for Grove modules, which ensure convenient installation and replacement of modules in the project. Compatible with LEGO. Set of 4. Seeed Studio 110070020

Board with digital outputs designed to work with STM32 Nucleo. It is based on the IPS1025HF single high-side switch arrangement. STMicroelectronics X-NUCLEO-OUT15A1

Qwiic adapter designed for micro:bit educational modules. Facilitates access to all pins that are led out on the connector with a pitch of 2.54 mm and the Qwiic connector. SparkFun BOB-16446

CAN controller module for Feather boards. It features an MCP2515 CAN controller and a TJA1051 transceiver and allows data transfer at speeds of up to 1Mb/s. Adafruit 5709

Module with a light intensity sensor LTR-329. It offers a measuring range from 1 to 65535 lux and a 16-bit resolution. Communication takes place using I2C. Adafruit 5591

Module with a pressure sensor with high accuracy HP206C. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020068

An adapter dedicated to programming STM32 microcontrollers in QFP100 chassis. It has a 20-pin JTAG/SWD connector and/or a 4-pin USART1 interface for programming and testing. Waveshare STM32-QFP100

Micro:bit expansion module designed for IoT. The board is equipped with WiFi, a two-channel output for DC motors, 6 IO pins, an I2C, UART interface, a buzzer, RGB diodes and a charging circuit. DFRobot MBT0012

An expansion board that enables the implementation of TCPP01-M12 functions and USB Type C surge protection for VBUS and CC lines suitable for sink applications. STMicroelectronics X-NUCLEO-SNK1M1

A small WiFi module designed for IoT applications. It can communicate with the motherboard via the I2C or UART interface. DFRobot TEL126

The IO expansion module is designed to work with the micro: bit educational board. There are 19 IO pins on the board, a buzzer and a voltage stabilization circuit are placed. DFRobot MBT0008

Module with a black and white OLED display 1.3" with a resolution of 128x64 pixels. Designed for M5Stack sets. It communicates via the I2C interface. M5Stack U119

Board with digital outputs designed to work with STM32 Nucleo. It is based on the IPS1025H-32 single high-side switch circuit. STMicroelectronics X-NUCLEO-OUT06A1

Versatile expansion module enabling support for high definition (HD) audio and video. It uses the advanced GAOYUN GW1NR series FPGA to generate the display signal and the LT8618S to process the output signal. M5stack M126

The 8MMINILPD4-EVKB is a complete development platform for embedded applications based on i.MX 8M Mini processors, featuring extensive I/O, wireless connectivity, and multimedia support.

Module with digital barometer BMP581. It enables pressure measurement in the range from 300 to 1250 hPa with an accuracy of ± 5 Pa and communicates via I2C or SPI. SparkFun SEN-20170

Memory adapter in SOP8 and DIP8 housings working with a voltage of 1.8 V dedicated to TL866CS/TL866A programmers