Category: STARTER KITS, PROGRAMMERS, MODULES

Module with WiFi and BLE Espressif ESP32-S3. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5477

Grove Breakout for LinkIt Smart 7688 Duo is a base plate for the IoT LinkIt Smart 7688 Duo module with Grove standard connectors. Connections include I2C and UART interface lines, analogue lines and ATmega32U4 digital microcontroller. The kit does not contain the LinkIt Smart 7688 Duo module. Seeed Studio 103030032

Module with three Hall sensors A3144E, which react to the failure of the magnet. It is powered with 5 V and has a digital output on the Grove connector. M5Stack U084

Comprehensive development platform for Espressif ESP32 a WiFi-compatible microcontroller and nearly 30 I/O pins. DEV-13907

Bascom compiler for AVR microcontrollers

Module with light sensor - LS06-S phototransistor. The board is equipped with a Grove connector and has an analog output. Seeed Studio 101020173

Starter kit with MKE16Z64VLF4 microcontroller. The board has an RGB LED, a 6-axis IMU sensor (accelerometer and magnetometer), a 3-axis digital gyroscope, an ambient temperature sensor, a CAN interface and a capacitive touch panel. NXP FRDM-KE16Z

Module with OTP-538U non-contact temperature sensor. The board is equipped with a Grove connector and has analog outputs. Seeed Studio 101020062

ESP32-S2-DevKitC-1U-N8R2 is an evaluation board featuring the ESP32-S2-SOLO-2U module, designed for developing wireless applications using 2.4 GHz Wi-Fi communication. The use of a U.FL connector allows for the integration of an external antenna, making it particularly useful in environments requiring extended range or signal isolation. With a wide range of available interfaces and large memory capacity, the board is ideally suited for IoT projects, building automation, remote control systems, and monitoring applications.

Module with light sensor - LS06-S phototransistor. The board is equipped with a Grove connector and has an analog output. Seeed Studio 101020132

The arduino turbidity sensor detects water quality by measuring level of turbidity. It is able to detect suspended particles in water by measuring the light transmittance and scattering rate which changes with the amount of total suspended solids (TSS) in water. SEN0189

J-Trace PRO for Cortex-M is setting a new standard for trace probes. It enables continuous streaming trace via its Gigabit Ethernet interface, lifting the limitations by internal buffers and slow data transmission. (j-trace-pro)

Module with heart rate and SpO2 sensor (oxygen saturation level) MAX30100 designed for M5Stack sets. M5Stack U029

STM32 Nucleo-144 development board with STM32F412ZG MCU, supports Arduino, ST Zio and morpho connectivity

nRF52 DK is a development board based on the nRF52832 system with Bluetooth Low Energy (BLE) and 2.4 GHz connectivity. The module has a connector compatible with Arduino shields, a connector for connecting an external antenna for NFC, buttons and diodes available to the user

Module with round 1.28" IPS LCD display and 240x240 px resolution and ESP-12E chip. SB Components 24025

RGB LED driver module designed for QT Py and Xiao boards. It uses a 3.3V/5V voltage level converter and allows to control 30 Neopixel LEDs. Adafruit 5645

NUCLEO-WBA55CG is a low-power STM32 development board with Bluetooth LE, Thread, and Zigbee support, designed for IoT projects. ST morpho and ARDUINO Uno V3 connectors enable flexible expansion and rapid prototyping.

Module with a gas concentration sensor MQ9, which enables the detection of carbon monoxide and combustible gases (methane, propane). The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020045

Module with liquid turbidity sensor. The board is equipped with a Grove connector and communicates via a digital or analog interface. Seeed Studio 101020752