New products
New products
zł59.04
Delivery date unknown
zł62.71
24h
Available
Grove Turbidity Sensor - liquid turbidity sensor
ID: 583100
5906623415335
zł133.75
Tax included
zł108.74 tax excl.
Module with liquid turbidity sensor. The board is equipped with a Grove connector and communicates via a digital or analog interface. Seeed Studio 101020752
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
Module with a liquid turbidity sensor that allows you to measure the amount of suspended particles in water. The process consists in checking the permeability of the tested liquid and the light scattering rate, which depend on the total amount of solid particles (TSS) in the liquid. An increase in TTS determines the increase in the level of turbidity. The sensor can operate in two modes: digital and analog. In digital mode, the particle level threshold is set with a potentiometer. The board is equipped with a Grove connector, so it can be used with the Base Shield V2 and Arduino extension. The module communicates via a digital or analog interface and is supplied with a voltage of 3.3 V or 5 V. It can be used to measure the quality of water in rivers, streams, aquariums, as instrumentation for monitoring pools, during sediment transport studies and even laboratory measurements. Full documentation with examples of use is available on the product page.
Features
- Measuring range: 0 to 1000 NTU
- Analog output
- Digital output (low/high state, threshold set with a potentiometer)
- Signal diode
- Output mode switch
- Supply voltage: 3.3 V or 5 V
- Dimensions: 40 x 20 mm
Kit contains
- Grove Turbidity Sensor module
- Probe
- Connection cable
- Grove cable
583100
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł113.90
24h
Available quantity: 11
Available
A set with ATmega2560 microcontroller (256 kB Flash, 8 kB RAM, 4 kB EEPROM) clocked at 16 MHz. The user has, among others: 54 I / O lines, 14 PWM channels, 16 analog inputs. Arduino A000067
zł209.00
24h
Available quantity: 66
Available
Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000
zł24.40
24h
Available quantity: 16
Available
The expansion module is designed for Arduino Mega and Google ADK boards. It is equipped with connectors to which you can attach modules compatible with the Grove standard. Seeed Studio 103020027
zł54.85
24h
Available quantity: 2
Available
Other products in the same category (16)
The module with the CY8C4014LQI touch sensor in the form of two buttons and a 5-segment slider. The board is equipped with a Grove connector and communicates via I2C. Seeed Studio 101020552
zł37.95
6 weeks
No product available!
5-port I2C splitter module. The board is equipped with Grove connectors and allows you to connect additional I2C devices. Seeed Studio 103020272
zł8.88
24h
Available quantity: 9
Available
Recorder v3.0 is a module that allows you to record and play sounds. The module was based on the ISD9160FI system, it also has a FLASH memory with a capacity of 2 MB, which allows for recording up to 83 seconds long. The set contains a small loudspeaker on which recorded sounds can be played. Seeed studio 107020029
zł101.32
24h
Available quantity: 2
Available
Module with an IR receiver operating at a frequency of 38 kHz. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020016
zł21.88
24h
Available quantity: 2
Available
The module with the ADIS16470 chip, which combines a 3-axis accelerometer and a gyroscope. The board is equipped with a Grove connector and communicates via the I2C or SPI interface. Seeed Studio 101020672
zł1,941.11
6 weeks
No product available!
MH-Z16 carbon dioxide sensor with Grove connector. It communicates via the UART interface. Seeed Studio 101020067
zł563.83
24h
Available quantity: 1
Available
Module with a 3-axis ADXL345 accelerometer with a configurable measuring range of ±2/±4/±8/±16 g. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020054
zł54.85
24h
Available quantity: 3
Available
Module with 5-way joystick. The board is equipped with a Grove connector and communicates via I2C. Seeed Studio 111020048
zł34.67
6 weeks
No product available!
Module with GPS receiver (SIM28). The system allows you to track up to 22 satellites. The UART interface is used for communication with the system. The module has a connector in accordance with the Grove standard. Seeed Studio 113020003
zł128.15
6 weeks
No product available!
Module with MLX90614 temperature sensor with a measurement accuracy of 0.2°C and a viewing angle of 5°. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020894
zł265.02
24h
Available quantity: 1
Available
A 4-core cable with a length of 30 cm, both terminated with a Grove plug. Seeed Studio 110990040
zł12.04
Delivery date unknown
No product available!
Module with a flame sensor or other light sources with a wavelength in the range of 760 to 1100 nm. It was based on the YG1006 sensor (photovolver NPN). The sensor has a connector compatible with the Grove standard. Seeed studio 101020049
zł41.02
24h
Available quantity: 2
Available
Controller with 5 m RGB LED strip (10 LEDs per meter). The LEDs are mounted on a flexible white PCB. Communication is via the Grove interface. Seeed Studio 104020005
zł91.65
24h
Available quantity: 2
Available
The expansion module is designed for Arduino Mega and Google ADK boards. It is equipped with connectors to which you can attach modules compatible with the Grove standard. Seeed Studio 103020027
zł54.85
24h
Available quantity: 2
Available
Module with 4 relays SRD-05VDC-SL-C with a load up to 10 A. The board was equipped with a Grove connector and communicates via I2C. Seeed Studio 103020133
zł76.58
24h
Available quantity: 2
Available
Module with the LIS3DHTR 3-axis accelerometer. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 114020121
zł24.06
24h
Available quantity: 3
Available
Module with liquid turbidity sensor. The board is equipped with a Grove connector and communicates via a digital or analog interface. Seeed Studio 101020752