Category: STARTER KITS, PROGRAMMERS, MODULES

Current-to-voltage converter module designed for devices with a current signal output. It allows linear conversion of current signals from 0 to 25 mA into voltage signals from 0 to 3 V. DFRrobot SEN0262

Audio module designed for Teensy 3.2, 3.5, 3.6 and 4.0. It uses the PT8211 16-bit digital to analog converter (DAC) chip. PJRC PT8211-AUDIO-KIT

The board with the RP2040 microcontroller equipped with two ARM Cortex-M0+ cores, which work at a frequency of 133 MHz, 256 kB RAM. The board also has 8 MB of QSPI flash memory. The system can be programmed in C/C++ or MicroPython. Adafruit 4884

Switch module with an interlock. DFRobot DFR0423

M5Stack series development kit equipped with ESP32 Pico. It will work in IoT-related projects or in "wearable" devices. M5Stack C008

ESP-PROG is an advanced tool for programming and debugging Espressif microcontrollers such as ESP32, ESP32-C3, ESP32-S2, ESP32-S3 and ESP8266. With the built-in FT2232HL USB bridge, ESP-PROG converts the USB 2.0 interface to serial and parallel interfaces, offering functions of automatic firmware download, serial communication and online debugging via JTAG

Development board based on Bluetooth Low Energy and IEEE 802.15.4 ESP32-H2-MINI-1 module. The ESP32-H2-MINI-1 integrates a 2.4GHz transceiver compliant with Bluetooth Low Energy and IEEE 802.15.4 technologies, supporting Bluetooth 5 (LE), Bluetooth Mesh, Thread, Matter, and Zigbee. Espressif Systems ESP32-H2-DevKitM-1-N4

The STEVAL-STLKT01V1 is a comprehensive development kit designed to support and expand the capabilities of the SensorTile and comes with a set of cradle boards enabling hardware scalability

Development board with NXP iMXRT1062 ARM Cortex-M7 microcontroller. Equipped with a microSD slot. Version without Ethernet communication. PJRC TEENSY41-NE-PINS

Crowtail – ESP8266 NodeMCU 2.0 is a universal WiFi module for IoT projects with a ready Crowtail interface, microUSB port, and Li-Po battery charging function. It works well in mobile and stationary applications based on Arduino IDE or NodeMCU Lua.

ESP32-S2-DevKitC-1 is a development board with Wi-Fi, ideal for IoT projects and breadboard prototyping. Espressif ESP32-S2-DevKitC-1-N8R2

Development kit based on ATSAMD51 with WiFi and BLE 5.0. It is equipped with a 2.4-inch LCD screen, IMU (LIS3DHTR), microphone, buzzer, microSD card slot, light sensor and infrared transmitter (IR 940nm). Seeed Studio 102991299

Module with EEPROM memory, capacity 512 kbit (64kB). Communication takes place via the I2C interface. The module has 3 jumpers that enable selection of one of 8 addresses. SparkFun SPX-14764

Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553

I2C-CAN converter using the MCP2551 and MCP2515 systems and the ATmega168PA microcontroller. The module uses the I2C bus and the Grove connector for communication. Seeed Studio 113020111

Module with a button, LED diode and a red cap. DFRobot DFR0029-R

Expansion module with a DAC/ADC converter and a camera dedicated to FireBeetle ESP32. It allows you to create versatile IoT applications. DFRobot DFR0498

A small USB-UART TTL converter module based on the CH340 system with a USB type A connector. Designed for the ESP-01 and ESP-01S modules

ATECC608A cryptographic chip module. Enables adding strong security to an IoT node, edge device or embedded system. Adafruit 4314