Category: STARTER KITS, PROGRAMMERS, MODULES

Module with digital barometer BMP581. It enables pressure measurement in the range from 300 to 1250 hPa with an accuracy of ± 5 Pa and communicates via I2C or SPI. SparkFun SEN-20170

OLED display with a diagonal of 1.3" and a resolution of 128x64 pixels. Designed for use with Feather series plates. Adafruit 4650

Ring light with 12 RGB diodes WS2812B type controlled by serial signal. The module can be powered with the voltage from 3.3 V to 5 V, only one signal line is required to control it. DFRobot DFR0888-12

Robot controller dedicated to Totem sets. It is based on the ESP32 chip (WiFi and Bluetooth module), equipped with a DC motor and servo driver, RGB diodes and an IMU sensor. With DC adapter and Li-Ion battery. Totem TE-X4-KIT3

Robot controller dedicated to Totem sets. It is based on the ESP32 chip (WiFi and Bluetooth module), equipped with a DC motor and servo driver, RGB diodes and an IMU sensor. With DC adapter. Totem TE-X4-KIT2

A set for building a smartwatch based on the micro: bit educational module. It consists of an expansion board and a strap

Ring light with 16 RGB diodes WS2812B type controlled by serial signal. The module can be powered with the voltage from 3.3 V to 5 V, only one signal line is required to control it. DFRobot DFR0888-16

Module with DA7280 vibration motor controller and LRA (Linear Resonant Actuator) motor. It allows you to add vibration feedback from the device to the project. SparkFun ROB-17590

Module with digital barometer BMP581. It enables pressure measurement in the range from 300 to 1250 hPa with an accuracy of ± 5 Pa and communicates via I2C. SparkFun SEN-20171

The 8MMINILPD4-EVKB is a complete development platform for embedded applications based on i.MX 8M Mini processors, featuring extensive I/O, wireless connectivity, and multimedia support.

The module with a heart rate sensor and the SpO2 level dedicated to micro:bit. It is based on the MAX30102 chip and communicates via the I2C interface. SparkFun SEN-15271

SBC6300X is an advanced single-board computer with a 32-bit ARM926EJ-S processor, designed for industrial, networking, and multimedia applications. A rich set of interfaces, the ability to run Linux and Windows CE, and an open architecture make it a universal solution for embedded projects.

ESP32-S3-DevKitC-1U-N8R8 board with Wi-Fi, BLE, 8 MB flash, and 8 MB PSRAM for IoT projects and AI applications. Espressif ESP32-S3-DevKitC-1U-N8R8

The module with SSR BT136S relay with a load of up to 2 A, designed for M5Stack sets. The board is equipped with a Grove connector and is controlled by a digital input. M5Stack U122

Micro:bit expansion module designed for IoT. The board is equipped with WiFi, a two-channel output for DC motors, 6 IO pins, an I2C, UART interface, a buzzer, RGB diodes and a charging circuit. DFRobot MBT0012

A set for building an interactive teddy bear-shaped pendant based on a micro:bit. It consists of a micro:bit v2 educational module, a scroll:bit module with a matrix display, a lanyard and a battery. Pimoroni PIM362

Module with MLX90614 temperature sensor with a measurement accuracy of 0.2°C and a viewing angle of 35°. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020895

Multifunctional expansion module dedicated to micro: bit V2. DFRobot MBT0042

Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip and communicates via the I2C or UART interface (Gravity connector). DFRobot SEN0518