Category: STARTER KITS, PROGRAMMERS, MODULES

Starter kit from the NUCLEO series equipped with STM32G031K8 (64 kB Flash, Cortex-M0+) microcontroller, with embedded ST-Link v.2.1 debugger, connectors compatible with Arduino Nano. STMicroelectronics NUCLEO-G031K8

Module with EEPROM memory, capacity 512 kbit (64kB). Communication takes place via the I2C interface. The module has 3 jumpers that enable selection of one of 8 addresses. SparkFun SPX-14764

ESP32-S2-DevKitC-1 is a development board with Wi-Fi, ideal for IoT projects and breadboard prototyping. Espressif ESP32-S2-DevKitC-1-N8R2

Module with WiFi and BLE Espressif ESP32-S3 system and LCD TFT display. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5483

8-port I2C splitter module. The board is equipped with a Gravity connector and allows you to connect additional I2C devices. DFRobot DFR0759

Module with an incremental encoder with a rotation range of 360°. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 111020001

Demo kit for prototyping applications and devices based on NFC ST25DV64KC tags. STMicroelectronics ST25DV64KC-DISCO

Board with SAMD21 microcontroller with CortexM0 + core (48 MHz, 256 KB Flash, 32 KB RAM). Equipped with WiFi and BT module (based on ESP32) and IMU LSM6DS3 unit. Ideal for applications in the IoT area. Module with headers. Arduino ABX00032

The NUCLEO-U031R8 evaluation kit is a development board with an STM32U031R8T6 (Arm Cortex-M0+) microcontroller, ideal for rapid prototyping of embedded applications. Equipped with 64 KB of Flash memory, 8 KB of RAM and numerous communication interfaces, it has Arduino and ST morpho compatible connectors and a built-in ST-LINK programmer, which makes it easy to integrate and test IoT and automation projects.

ESP32 module board equipped with a 1.28-inch round display with touch panel. It offers Wi-Fi and Bluetooth 5.0 communication, has a built-in 6-axis QMI8658 IMU sensor and supports lithium battery charging. Ideal for developing IoT projects, mobile devices and wearable electronics. Version with metal housing. Waveshare ESP32-S3-Touch-LCD-1.28-B

Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553

Board with the WiFi Espressif ESP32-S2 module. It offers 4 MB of Flash memory and 2 MB of SRAM and an RGB LED. It is equipped with a STEMMA QT connector. Adafruit 5325

Module with SPDT switch. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020004

Standard 20-pin 0.1 male connector to provide electrical isolation, Segger

Crowtail – ESP8266 NodeMCU 2.0 is a universal WiFi module for IoT projects with a ready Crowtail interface, microUSB port, and Li-Po battery charging function. It works well in mobile and stationary applications based on Arduino IDE or NodeMCU Lua.

Two axis stepper motor driver expansion board based on the L6470 for STM32 Nucleo

Bluetooth 5.2 and IEEE 802.15.4 communication kit. It uses the STM32WB55RG microcontroller (1 MB Flash, 256 KB SRAM, ARM® Cortex®-M4 and Cortex®-M0 +). STMicroelectronics NUCLEO-WB55RG

Module with tact switch button. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020003

STM32 Nucleo-64 development board with STM32L073RZT6 MCU, supports Arduino and ST morpho connectivity