Category: STARTER KITS, PROGRAMMERS, MODULES

Expansion module compatible with micro:bit. The board is equipped with a 24 V 2 A relay, two buffer inputs, two sink outputs and three analog inputs with a working range up to 24 V. Pimoroni PIM371

Blue mounting for Grove modules, which ensure convenient installation and replacement of modules in the project. Compatible with LEGO. Set of 4. Seeed Studio 110070026

The power module is designed to work with BBC micro:bit boards. It is equipped with a buzzer and a CR2032 battery socket. Kitronik 5610-V2

The STM32F4DISCOVERY kit leverages the capabilities of the STM32F407 high performance microcontrollers, to allow users to easily develop applications featuring audio

Module with a GPS receiver based on the MTK3333 chip. It is equipped with a STEMMA QT connector and communicates via the UART or I2C interface. Adafruit 4415

STM32 Nucleo development board for STM32 F0 series - with STM32F072RBT6 MCU, 128KB flash memory, STM, RoHS

WiFi module with ESP8266 designed to work with the Raspberry Pi Pico. It communicates via the UART interface using AT commands. Waveshare Pico-ESP8266

Module with WiFi Espressif ESP32-S2 WROOM. It integrates a set of peripheral devices - capacitive touch sensors, SPI, UART, I2S and I2C. SparkFun WRL-15663

The nRF7002 is a board that allows you to add Wi-Fi connectivity to the Nordic Thingy:53 development kit. It connects to the Thingy:53 edge connector and enables the development of Wi-Fi 6 applications for low-power applications. Nordic Semiconductors nRF7002-EB

J-Link 9-pin Cortex-M Adapter, RoHS, Segger

Module with heart rate and SpO2 sensor (oxygen saturation level) MAX30100 designed for M5Stack sets. M5Stack U029

Module with proximity and ambient light sensor based on the VCNL4020 system. It allows you to detect obstacles in the range from 0 to 20 cm and measure light intensity from 0.26 to 16,000 lux. It communicates via the I2C bus. Adafruit 5810

Photoelectric liquid level sensor FS-IR02 in a set with a Gravity adapter. DFRobot SEN0205

J-Trace PRO for Cortex-M is setting a new standard for trace probes. It enables continuous streaming trace via its Gigabit Ethernet interface, lifting the limitations by internal buffers and slow data transmission. (j-trace-pro)

Ultrasonic distance sensor with a range of up to 5 m with an analog output The module is supplied with the voltage from 3.3 to 5.5 V. DFRobot SEN0307

Adafruit 1222

This module allows you to add MIDI input and output to your Feather board, utilizing DIN-5 connectors and a built-in 3V optocoupler for secure 3.3V communication. The module also features LEDs to indicate data transmission and optional 3.5mm TRS MIDI sockets for the TRS MIDI A standard. It communicates via a hardware UART set to 31250 baud, allowing for easy integration with Adafruit 4740 MIDI instruments and controllers.

NUCLEO starter kit featuring an STM32U385RG microcontroller (1 MB Flash, Cortex-M33), a built-in ST-Link/V3 programmer-debugger, and Arduino-compatible connectors. STMicroelectronics NUCLEO-U385RG-Q

Two-button module with 4 colored overlays. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 111020103

Module with EEPROM 24LC32 memory with a capacity of 32 kBit (4 kB). Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5146